Question about Motherboards

1 Answer

Usb device i put usb in my computer but it have a problem and

Posted by on

  • 1 more comment 
  • David Shaub May 11, 2010

    What computer, what operating system, what USB device, what problems?

  • DEKR
    DEKR May 11, 2010

    please explain

    are you getting an error message

  • Amardeep46
    Amardeep46 May 11, 2010

    Please provide complete details of the problem

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,602 Answers

Go into control panal open up new hardware adding,adding hardware .

or device manager and click on usb devices and see if anything is wrong like yellow or red marks of any kind than click on it and follow instructions

rod

Posted on Feb 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix the msi motherboard windows 7 USB error 43?


How to Fix a Code 43 Error

  1. Restart your computer if you haven't done so already.

    There is always the chance that the error Code 43 you're seeing on a device was caused by some temporary problem with the hardware. If so, a restart of your computer might fix the Code 43 error.

    Note: Some users have also reported that powering off their computer completely (not just a reset) and then turning it back on has corrected their Code 43 issue, especially if it exists on a USB device. In the case of a laptop, turn it off and remove the battery, wait a few minutes, and then put the battery back in and start the computer.
  2. Did you install a device or make a change in Device Manager just before the Code 43 error appeared? If so, it's very possible that the change you made caused the Code 43 error.

    Undo the change if you can, restart your PC, and then check again for the Code 43 error.

    Depending on the changes you made, some solutions might include:
  3. Reinstall the drivers for the device. Uninstalling and then reinstalling the drivers for the device is a possible solution to a Code 43 error.

    Important: If a USB device is generating the Code 43 error, uninstall every deviceunder the Universal Serial Bus controllers hardware category in Device Manager as part of the driver reinstall. This includes any USB Mass Storage Device, USB Host Controller, and USB Root Hub.

    Note: Properly reinstalling a driver, as in the instructions linked above, is not the same as simply updating a driver. A full driver reinstall involves completely removing the currently installed driver and then letting Windows install it over again from scratch.

Sep 16, 2012 | MSI INTEL G41 INTEGRATED VGA-MATX 2DDR3...

1 Answer

Logitech wirless mouse light on top but not bottom and does not work...put in new batteries...still does not work


make sure the usb device is inserted correctly into your computers usb slot you might have remove it restart your computer then reinsert it or you might go for safe mode
restart your computer repeatedly tapping the f8 key to enter safe mode while the screen is black once in safe mode where the only things working will be your keyboard and mouse allowing you to attempt to repair your computer
click start right click on my computer select properties device manager control scroll to mice and pointing devices you might see a yellow question mark? right update driver in
make sure the battery is good ((has full charge))also you might test the usb device for the mouse is inserted correctly into the usb port (if applicable)
Windows 7
hope this helps

Jul 16, 2011 | Motherboards

1 Answer

Hi my computers usbs are not working i have a other set of usbs that i put in my computer but the one that came when i bought it do not work now but the once did. I am now stuck using 4 usbs and the other...


click start control panel administrive tools computer management device manager scroll down universal serial bus controllers you could see a yellow question mark?

right click to reinstall drivers

if you can see your usb drive but its not working

ports(com&lpt)right click update driver if this fails to fix the problem

check the USB leads that attach to the motherboard usually red white green black make sure they are securely seated and have no dust build up on them dust will cause static and a lot of unforeseen problems for a computer and its parts

click start control panel administrive tools ,computer management ,device manager look through all of your devices if you see a yellow question mark?or exclamation mark ! or red x

right click to reinstall drivers

hope this helps


Jun 20, 2011 | Motherboards

1 Answer

I recently installed the logitech mk550 keyboard/mouse combo on my desktop and it put my computer to sleep, now it won't come out of sleep mode and rebooting doesn't work, the computer stays asleep. Any...


Unplug the usb receiver as well as all other usb devices plugged in. Unplug your desktop from the power outlet. While unplugged, press and hold the power button for around 10 seconds to drain the power. Plug the power back but not the usb devices. See if it now boots up.

Apr 06, 2011 | Motherboards

1 Answer

My usb ports do not working.When I put my mouse in it, the mouse lights become on but in the desktop the pointer is on its place and no hardware are found.I check 3 more mouse and key boards but the...


Follow the steps given below to refresh USB ports.

1. Right-click My Computer icon on the desktop, and then select Properties.
2. Click the Hardware tab.
3. Click the Device Manager button.
4. Click the plus (+) sign to the left of Universal Serial Bus controllers.
5. Right-click the device listed under Universal Serial Bus controller and select Uninstall.
6. Click OK to confirm the removal of the device.

Please note, repeat Steps 5 and 6 until all the devices under Universal Serial Bus Controller are removed.

7. Shut down the computer.

CAUTION: Ensure that the Shut Down option is selected, instead of the Restart option.

8. Wait for 5 seconds and then restart the computer. When the computer restarts, a "Windows has detected new or added hardware" message window will open.

The above steps will refresh the USB ports.

Now connect the USB devices like mouse, video camera, your external usb hard disk...usb hubs...whatever you like and the drivers should install automatically.

Tip: It is always recommended to connect the main usb devices at the rear end usb port, as they require more power to initiate.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe


Apr 01, 2011 | Intel PENTIUM-4 865GV CHIP MOTHER BOARD...

1 Answer

I have a Verbatim USB250 (JH8522), when I connect the USb to my laptop, 1st do not appear on my Computer devices, 2nd the blue light is flashing continuously, and is suppose to stay lid.


Try to put the USB to some other port. Try to put the same USB to some other system to confirm whether the problem is in the port or in th USB.

Jan 14, 2011 | Motherboards

1 Answer

Computer won't read my camera memory card...


Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} First, you want to rule out any problems with the device itself. A good way to do this is to blame the USB device into a different computer to see if it works there, if it doesn’t work in a different computer and the problem is with the device itself. USB devices, although very handy and portable can fail just like any other device

However, if the USB device works in another computer system than the problem lies with the configuration of the computer where the device did not work

Follow the steps below to troubleshoot this scenario and make your USB device work

1) If you are using a USB cable with your device, check the cable to make sure it matches the speed of the device. Use USB 2.0 cables with USB 2.0 devices and USB 1.1 cables with USB 1.1 devices. Swap cables and check the device, if this does not work, proceed to Step 2.
2) Next, open Device Manager and look under the heading for USB Serial Bus Controllers. If there is a device with a yellow exclamation mark next to it such as USB Mass Storage Device. Double-click on the entry and check the Device Status. If the status shows something like
"This device cannot start. (Code 10)"
proceed to Step 3.
3) The easiest way to solve a USB error code 10 in Windows XP is to follow the steps below to remove and reinstall all USB controllers.
A. Click on Start
B. Right Click on My Computer, click on Properties
C.Click on the Hardware tab
D. Click the Device Manager button.
E. Expand Universal Serial Bus controllers section.
F. Right-click every device under the Universal Serial Bus controllers node, and then click Uninstall to remove them one at a time.
G. Restart the computer, and allow the computer to reinstall the USB controllers.
H. Plug in the removable USB storage device, and then test to make sure that the issue is resolved.



Feb 24, 2009 | Gigabyte GA-8IG Motherboard

1 Answer

Bios setup error


Unplug ALL Usb devices, that includes printers, cameras, pen drives, i.e. anything that plugs into a USB connector. Then try rebooting your computer. I bet your problem will no longer exist, but if it does, then you need to suspect a faulty USB connector on the motherboard or USB chipset located on the motherboard. Once the computer is booting normally without USB devices hooked up, you can start installing ONE Usb device at a time, until you find your defective USB device. The USB device drivers will need to be installed and computer rebooted at least once between the various devices. Not doing so will lead to confusion as to which USB device is causing your high current problem. It is also possible athough a bit unlikely that this procedure will cure your situation for the time being but look out for it in the future because it could be an early sign that one of your USB devices is going bad.

Aug 11, 2008 | ASUS P5PE-VM Motherboard

1 Answer

Usb 2.0


Hi,
this is a common error with operating systems and devices.
If you go into my Computer/system/device manager. And remove the installed USB devices. shutdown the computer, and reboot it. then try putting your USB device in.
What general happens, is that if you have had an older device in the USB port at any time, the port configures itself to this setting. options are to try another port on the computer ( some older ports only support usb1.1 )
ensure you have up to date drivers on the connecting device and on the connecting computer.
Hope this helps Mike @ Compurepair.

Feb 22, 2008 | ASUS M2A-VM (0610839149438) Motherboard

Not finding what you are looking for?
Motherboards Logo

Related Topics:

1,211 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motherboards Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Mark Taylor
Mark Taylor

Level 3 Expert

728 Answers

Are you a Motherboard Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...