Question about Hoover Nextra HNWL 3136 Front Load Washer / Dryer

2 Answers

Program don't start, flashing ligths (start and "delay start" button) for 5 times.

No problem with power but when the machine tries to start the program make some noise and stops with the error code indication of 5 times flashing. Many thanks.

Posted by on

  • antonio andrade Aug 01, 2007

    Thank you for the answer.
    Unhappily the problem is not in the water supply. The inlet valve solenoid is ok. I get the same error if a the start.

    About the error : the meaning is not is the user guide (this is techinal stuff) ! Do You a have an idea where i can get the error description.

    The machine has 25 months old and Hoover assistance requested me 130 ? ( ~87£) only for a repair proposal !

    I think that the problem is related with the out of balance sensor. Some days before the breakdown the machine start to claw clothes !

  • antonio andrade Aug 02, 2007

    Thanks for trying.
    Regards

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hoover wd 1400 error 1

Posted on Jan 25, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,985 Answers

What does the error code mean do you have any idea Is it mentioned in the Hand book. At any rate logic suggests a watewr supply problem that the first thing a washing machine needs - water. So a tap not turned on a Kinked hose An inlet valve solenoid failure- Three things for you to check

Posted on Jul 31, 2007

  • john ash
    john ash Aug 02, 2007

    I cant help further with tnis one -sorry

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Whirlpool front load washer keeps resetting the delay start time. I don’t want any delay, but it keeps resetting itself to 45 minutes. Can you help?


could be the delay button is activating intermittently? try pressing it hard couple of times ...don't break the butoon :)

Nov 22, 2017 | Whirlpool Washing Machines

1 Answer

Model EWF10843. How do I select diagnostic mode?


Electrolux Diagnostic Mode
* Press the Cancel button to enter standby mode and enable diagnostic entry.
* Within 10 seconds after pressing Cancel , press any button to wake up the control.
* Within 5 seconds of wake up, turn the selector knob to the far left cycle and press and hold Cancel and far left
button under the display simultaneously for 3 seconds to enter the diagnostic mode.




To save time at wake up, the Welcome screen can be bypassed by turning the selector knob.





1. Upon entering diagnostic mode, all lights should flash for 1¼"x2" display models and all lights on for the 1¼" x
4 3/4" display models.
2. Turn the program knob (1) click clockwise from the start position. The hot water solenoid will activate and hot water
should enter through the detergent compartment.
3. Turn the program knob (2) clicks from the start position. The bleach water solenoid will activate and cold water
should enter through the bleach compartment.
4. Turn the program knob (3) clicks from the start position. The bleach and the wash water solenoids will activate and
cold water should enter through the softener compartment.
5. Turn the program knob (4) clicks from the start position. The prewash solenoid will activate and cold water should
enter through the prewash compartment.
6. Turn the program knob (5) clicks from the start position. The door lock solenoid will deactivate and the loading door
can be opened. When the door is opened, the drum light should turn on.
7. Turn the program knob (6) clicks from the start position. The door lock will activate and the washer will fill then
tumble. Once tumbling has started, the boost heater will turn on.
8. Turn the program knob (7) clicks from the start position. The drain pump will activate draining out any water in the
tub and the washer will operate in high spin.
9. Turn the program knob (8) clicks from the start position. This is a free position.
10. Turn the program knob (9) clicks from the start position. The control will signal the last 5 error codes with E00
being no error.
11. Turn the program knob (10) clicks from the start position. Latest software version will be shown.
12. If applicable, turn the program knob (11) clicks from the start position. This is a free position




Exiting Diagnostic ModeA) Unplug the power cord, wait 5-8 seconds, then reconnect the power cord or
Turn the program knob clockwise back to the start position. Press the Cancel and far left button under the display

until the LED's stop flashing

Jun 08, 2015 | Electrolux Washing Machines

1 Answer

Flashing key


Sounds like have inadvertently activated the child lock, select any program and press and hold the start button until the key light goes off approx 5-10secs. If this does not work please repost with model number as with some bosch models it is a different button you need to hold. (may be the time delay)

Mar 16, 2013 | Bosch Washing Machines

1 Answer

I have an Electrolux EWD1477. I have been away for four months and I'm having problems with it. I set to do the quickwash30 program and press start, you hear the clicks, it might put some water in then...


My EWD1477 was doing this a year ago and I fixed it. Then it started doing it again a month ago and I seem to have cleared it again.

Firstly, remove the drain hose from where it is inserted into a laundry sink hole to make sure it is not blocked or sealed in with sludge.

Secondly, make sure the machine is empty of water and clothes and then turn the machine to off with the Program Selector Dial. Then turn off the power at the socket and remove the power plug and leave for five minutes.

Step 1: put the plug back in and turn the power back on.

Step 2: turn the selector switch to the right (Whites/Intensive). The green light of the Start/Pause button should be flashing and the green lights on for Prewash/wash, Rinses and Spinning. Don't press any other buttons or change any other settings.

Step 3: press the Start/Pause button and wait for the machine to empty any excess water. Press it again immediately after you hear water flowing into the machine OR two audible clicks. The machine is now in pause mode with the green light of the Start/Pause button flashing. Only the green light on the Prewash/Wash button should be on. Leave it in pause mode for 30 minutes and then press the Start/Pause button to recommence the cycle.

Step 4: If the Start/Pause button begins flashing, water stops flowing into the machine and the three green lights mentioned above are back on, turn the Program Selector Dial back to off, wait 10 seconds, and repeat the process above.

Step 5: If when you then turn the Program Selector Dial to Whites/Intensive and hear the two audible clicks, immediately press the Start/Pause button to set the machine in pause mode. Wait 30 minutes. Then press the Start/Pause button to recommence the cycle.


Hopefully the cycle will run without a problem.

Mar 26, 2011 | Electrolux Washing Machines

1 Answer

Asko Dryer t760 program menu won't change or is frozen The program menu is stuck on one setting, and the P1, P2, P3, P4 buttons don't change the program. When I try to reset the program (by pressing...


Hello,

Welcome to FixYa.

By stating "the dryer does work" indicates it is likely an issue with programming.

What are the chances you have the menu lock-out option turned "on"...also referred to as "child lock".

You may quickly rule this out or confirm it is the problem indeed, by trying this.

CHILD-SAFE START

1. Turn the machine off then on.
2. Press ENTER five times, then press P3 five
times. (This must be done within 15 seconds.)
3. “Delayed start” displays with “0” flashing in the
lower right corner. Press the Right Arrow button
to toggle the display to “3.”


**NOTE: Child-Safe Menu Button**
Please note that when you set the child-safe Start
button, the Menu button is automatically
programmed to delay for three seconds before it
becomes active. This prevents a child from
accidentally changing the program settings.
When you want to change a program, press the Menu
button for three seconds to activate the menus. The
Menu button will work normally (without the
three-second delay) until you have completed your
changes. If it is not pressed for two minutes, it will
automatically revert back to the child-safe mode.

Let me know if this indeed solves the problem but either way please keep me posted.

Thank you for choosing FixYa and good luck.

Regards,

Macmarkus :)

Sep 18, 2010 | Asko T761 Electric Dryer

1 Answer

Hoover HNL 662. 'Delay start' light comes on and stops machine


my hoover nextra hnl 662 want wash or spin and the delay staart light flashes 5 times please help iv only had the machine a year and had nothing but trouble with it wouldnt recomend one of these washing machines to anyone jakki

Feb 16, 2010 | Hoover Nextra HNL 3166 Z Front Load Washer

3 Answers

Hoover HNL7166 'Start Delay' light flashing


Hoover (Nextra series) washing machines

The 'Start' & 'Pause' LED's will flash together to indicate the error code. You have to count the flashes within each 15 second period to get that error code. The start and the pause LED's will flash together at 1Hz (i.e 1 flash per second) within that 15 second time frame, then will continue and show again within another 15secs and so on.

1 Flash = Interlock fault
2 Flashes = Fill time-out
3 flashes = Drain time-out
4 flashes = Overfill fault presure pipe blocked
5 flashes = NTC error
6 flashes = faulty control board
7 flashes = Motor jammed
8 flashes = Tacho fault
9 flashes = Motor triac on module board
10 flashes = Prog Selector or wiring fault

Jul 27, 2009 | Washing Machines

1 Answer

Zanussi 1000XC Washing Machine - Pause Light Flashing


The ECU is failed. unplug for 40 minutes to try to reset it.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Mar 16, 2009 | Washing Machines

2 Answers

Breadmaker Won't Start


I had the same problem. Check the delay start button even though it doesn't tell you to. To get my machine to work the first time I used Menu #3 (which does not have a delay start) and it worked. Then I tried to use the dough cycle and it wouldn't go either, so I unplugged the machine, plugged it back in, went to Menu # 3 first to see the time (which was 1:50) then I checked the delay time to make sure it was also set at 1:50. Mine was not (it said 2:00) so I moved it down to 1:50 and it started 15 minutes later. I really don't like this 15 minute delay on this machine. I am going to try regular bread later and I will make sure that the delay time is the same as the time given for completing the loaf ( ie make sure it says 3:30 NOT 13:30. I hope this works.

Feb 09, 2008 | Black & Decker B2000 Bread Maker

Not finding what you are looking for?
Hoover Nextra HNWL 3136 Front Load Washer / Dryer Logo

886 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

shaun taylor

Level 3 Expert

1527 Answers

Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...