Question about Linksys WRT160N Wireless Router

1 Answer

Login and password

I put my user name in and password in, but it does not recognize

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Try to restore it to factory default.

Posted on Jan 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Login Page Error


reset you router, put the default id and password, the address to put in your bowser is http://tplinklogin.net/

Mar 14, 2014 | TP-LINK Routers

1 Answer

Hey,im needing immediately the password of the motorola sb5101i when i type in adress bar 192.168.1.1 it ask login and password but i dont know the login or password and i really need it i need to change...


HI i beleive you are looking for a user name and password for the motorola sb5101i

here are the username and password for the modem which are default

USER NAME:-ADMIN

PASSWORD:-leave it blank>>press login(this should work)

DEFAULT IP FOR YOUR MODEM:-192.168.100.1

IF THIS doesnt work try to turn off the modem and turn it on back...this might work

or else you can try to reset the modem,once this is done you might have to reconfigure the modem...contact your internet service provider to set it up

Apr 25, 2011 | Routers

1 Answer

I am unable to setup a security password for my wireless network on my Apple Macbook using D-link wireless router model DIR-615


Enter a new login name and a new password for the administrator login. if you are a user then enter a new password and login name into the user login.

Apr 04, 2011 | D-Link DIR-615 Wireless Router

1 Answer

Don't understand how to set password. please help


Plug the router into the power socket and configure you own machine to obtain IP address automatically. Load up Internet explorer and type in http:/192168.xxx.xxx which is the local address of your router. You should then get a password screen. Enter default user name and password and it will take you to the configuration screen. The full IP address and user name and password are dependant on which model you have. See list below From there you need to read the instructions very carefully and match it with the information provided by your ISP.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response. Happy Holidays!

Thanks, Joe
? Q: What is the default IP address, username, and password for routers? ? A


ZSR0104
192.168.8.1
Administrator password: admin

ZSR0104M
192.168.1.1
Login password: No Password

ZSR0104B
192.168.1.1
User Name: admin
Password: 0000

ZSR0104AS-01
192.168.8.1
Administrator password: No password

ZSR0104E
192.168.2.1
Login password: No Password

ZSR0104CP (Grey color)
192.168.1.1
User Name: admin
Password: admin

ZSR0104CP-05 (Blue color)
192.168.10.1
User Name: guest
Password: guest

ZSR0104WE-01
192.168.2.1
Login password: No Password

ZSR0104WE-04
192.168.2.1
User Name: admin
Password: 1234

ZSR0104WE-05
192.168.1.254
User Name: admin
Password: 1234

ZSR1104WE
192.168.2.1
User Name: Empty
Password: Empty

ZSR0104DE
192.168.2.1
Login password: No Password

ZSR0104FS
192.168.1.1
User Name: admin
Password: admin

ZSR0104UP
192.168.1.1
User Name: admin
Password: 0000













Dec 22, 2010 | Zonet Routers

1 Answer

I forgot my user name and logon domain


If you've forgotten the Router password, then press the Router Reset button (a small point) located next to the Ethernet port on the Router to restore the Router to factory settings.
After resetting the Router to factory defaults, use the default name and password.

Router Login: http://192.168.1.1
Login Name: admin
Login Password: password

Jul 02, 2010 | NetGear WNR2000 Wireless Router

1 Answer

My moms cable company installed a new modem and left the router disconnected--I reinstalled the software and hooked everything back up and my laptop recognizes the network but seems to be stalled out at...


Hi ,

This is Neo . Thanks for contacting us .

Reset your Netgear and Try it again .

The step to be followed are ,

STEP 1

Reset the Router by pressing the RESET button on the rear till the Test Light blinks.This takes about 10 seconds . Use a pen or paper clip to access it .
Release the button and wait for the Router to Reboot.

STEP 2

Login to the Router with the default Password. The Router has the default User Name as 'admin' and the default Password is 'password' .

STEP 3
If the Router was not cleared after rebooting, unplug the Router's power . Then Press and hold the Reset button.

STEP 4

While the button is held down, reconnect the Router's power . Continue to hold the Reset button for 20 seconds after reconnecting the power . Wait for the router to reboot .

Then Login to the Router with the default Password. The Router has the default User Name as 'admin' and the default Password is 'password' .

Do the setup and try to connect to internet .

The Router will work .

Thanks & Regards
Neo

Thanks for using FixYa.com.

Feb 07, 2010 | NetGear WGT624 Wireless Router

2 Answers

I cannot configure the DLink DAP 1150 access point .As said in the manual When I put the user name and start it says that password is not valid.what is the solution?


Reset the device, unplug all network cable before power on (to turn off dhcp function). After that connect the network cablethe ip device should 192.168.0.50 and subnet mask 255.255.255.0. Set your computer ip address to 192.168.0.xxx where xxx is not 50. Access the device via your web browser, the login page should be apear. User : admin, password : leave it blank

Jan 06, 2010 | Routers

1 Answer

Reset a password for IBM NWAYS Router 2210 Model 12E


Does this mean anything to you Remote Login Names and Passwords During a remote login, the device prompts you for a login name and password. You can display the login name when logged in to the device from a remote console by using a device status command. Logging in Remotely or Locally Logging in to a local console is the same as logging in to a remote console except that you must connect to the device by starting Telnet on your host system. To log in remotely, begin at step 1. To log in locally, begin at step 3. To log in from a remote console: 1. Connect to the device by starting Telnet on your host system. Your host system is the system to which remote terminals are connected. 2. Supply the device?s name or Internet Protocol (IP) address. To use device names, your network must have a name server. Issue either the device name or the IP address as shown in the following example: % telnet brandenburg or % telnet 128.185.132.43 At this point, it makes no difference whether you have logged in remotely or locally. 3. If you are prompted, enter your login name and password. login: Password: It is possible that there is a login and no password. The password controls access to the device. If a password has not been set, press the Enter key at the Password: prompt. Logins are not set automatically. For security, you can set up user names and passwords using the add user command in the CONFIG process. For additional information, see the add user configuration command, on 56. Remember to reload or restart to activate any changes. Note: If you do not enter a login name and valid password within 1 minute of the initial prompt, or if you enter an incorrect password three times in succession, the device drops the Telnet connection. 4. Press the Enter key to display the asterisk (*) prompt. You may have to press the Enter key more than once or press Ctrl-P to obtain the * prompt. Once at this level, you can begin to enter commands from the keyboard. Press the Backspace key to delete the last character typed in on the command line. Press the Delete key or Ctrl-U to delete the whole command line entry so that you can reenter a command. See ?Command Completion? on page 20 and ?Command History? on page 23 for more information. You can also use local Telnet commands on your Telnet client to close the Telnet connection.

Jan 21, 2007 | IBM NWAYS Router 2210 Model 12E

2 Answers

What is the default user name and password to login the Prestige via the browser?


To restrict only the adminstrator can configure the router, there is a login procedure prompted for asking User Name and Password. The default User Name is 'admin' and the default password is the default SMT password, '1234'.

Feb 19, 2006 | Zyxel Prestige 310 (AM406100) Router

Not finding what you are looking for?
Linksys WRT160N Wireless Router  Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Linksys Routers Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Mike

Level 3 Expert

4331 Answers

Steve

Level 3 Expert

3287 Answers

Are you a Linksys Router Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...