Question about Sony Office Equipment & Supplies

1 Answer

My picture slants in towards the top from bottom

Why is the picture like this, It doesn't matter where I place the projector the picture always slants inward toward the top from the bottom.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

The issue has to do with something called "Keystone". This allows you to set the projector at an angle and project on an angle. When you set the projector on a flat surface, you would need to adjust the keystone to get rid of the "trapazoid" look of the image.

Posted on Jan 31, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you open the front of the Infocus Screenplay 4850 after taking the screws out? The top seems to be stuck and I don't want to break it. I'd like to find somewhere I can see all the parts seperated...


If all screws are out of the bottom and the rear of the unit, pop the outer ring of the zoom/focus assy off using a wide flathead. Then flip the unit on it's back with the lens towards you. Grab the bottom of the front bezel with both hands and pull the bottom towards you until it pops out. At this point you should be able to see the clip things that are part of the top that the front snaps into. Place your flathead under the clip and twist up a little while pulling on that side of the front. Repeat for the other side of the front. Do the same for the rear.

Oct 22, 2010 | InFocus ScreenPlay 4805 Multimedia...

1 Answer

The top of the screen is slanted while the sides of screen and bottom are even, causing the right hand side of screen to appear smaller than the left. Anyway to fix this?


Sounds like a "keystone" problem. Your projector needs to be oriented to the screen in an exact manner. Manufacturers provide "keystone" correct to adjust for mis-alignment. If proper orientation is impossible, use the keystone correction of the unit to adjust your edges.

Aug 14, 2010 | Hitachi Cine Master PJ-TX200 Multimedia...

1 Answer

Picture is cut off top and bottom (Infocus 7210 projector)


try different ratios, also reflash firmware and lastly try new cables.

Jul 14, 2010 | InFocus ScreenPlay 7210 Multimedia...

1 Answer

The projector is approximately 4 years old & on average runs for about 60 hours per week, 40 weeks of the year. After fitting a new lamp last October & resetting the projector, the image is still...


Additional information is required for us to assist. Can you better describe what you mean by "poor image"? Are the colors separated? Is the picture out of focus? Are the colors wrong?

Please describe the picture or post a picture of the screen if you can.

Thanks,
Dan

Feb 03, 2010 | Sanyo PLC-XP57 LCD Projector

1 Answer

The picture being projected is like a slanted box. one side is straight and the other side slants -- I have moved the keystone and it doesn't help


the light tunnel is collapsing and needs to be replaced. common problem with this model. you could buy the part and replace it yourself, but it's pretty difficult and involved. or you could send it in to an infocus service center for repair. either way, try av solutions in ny. they're good. www.avsolutionsny.com

Dec 03, 2009 | InFocus LP70+ Multimedia Projector

1 Answer

Picture on screen is cut off


reset the settings to factory default. if that does not clear it up, there is a sync issue. try a different cable. otherwise, there is a problem with the main board.

Jul 08, 2009 | InFocus LP 340B Multimedia Projector

1 Answer

Slanted Border- Projector image is not square


Is the image slanted on the bottom as well?
Make sure the projector's throw is pointed directly at the target ie. screen or wall etc. there's not much else it could be.

Jan 10, 2009 | InFocus ScreenPlay 4805 Multimedia...

1 Answer

Picture not square


keystone should help in your opinion. adjust the keystone and the picture should be a square then.

Oct 28, 2008 | Hitachi CP-X275 Multimedia Projector

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

514 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Office Equipment & Supplies Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

69570 Answers

easy alberta
easy alberta

Level 2 Expert

132 Answers

Are you a Sony Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...