Question about Goldstar DH504EL Dehumidifier

Open Question

GE refrigerator wiring diagram

Need wiring diagram for GE frig, icemaker not working, solenoid not opening to allow water to icemaker please send for me , wirring diagram of electrical refrigerator

Posted by on

  • John Tripp
    John Tripp May 11, 2010

    Look at following areas for the model number


    • Beneath Or Inside Food Compartment On Cabinet Frame
    • On Plate Lower Front Or Rear Of Cabinet
    • Beside Compressor Door On Right End
    • Near Rear Of Cabinet
    • Inside Liner At Top

    Let us know the numbers and we will help you find the wiring diagram.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace the humidity sensor


Only two wires and two screws. Shut off the furnace disconnect switch before doing anything. Then Pull off the cover and I do mean pull off. Then undo the two screws remembering what terminal they go to. Remove the screws from the back plate and let the wires fall through the back plate as you pull it off the wall or duct. Put the new back plate in place with the wires pulled thought. Install the screws I the same place as the old ones. Re attach the wires into the same labeled terminals as the old one. Put the new cover on. Turn on the furnace disconnect switch and away you go. To check operation all you need to do is, turn the knob on the humidifier control and listen for the solenoid to open and water to flow to the humidifier. If nothing happens then you need to check for power to the humidistat. Should be 24v. If no power then you need to check the source.


good luck

Apr 19, 2014 | Dehumidifiers

1 Answer

De'Longhi DE500P quit working after a couple of seasons. The unit is like new. All lights work, everything seems to be running, but no water is extracted. De'Longhi wants me to send it to Ohio,...


Paul, There are 5 basic, yet solvable reasons for what you described. Please pay particular attention to numbers 1 & 2..

1. The humidity extraction level is set to HIGH. Lower it to 32-35%.

2. Air intake filter is dirty or clogged. Turn unit OFF, & Unplug the
Unit, before removing to inspect & clean it, if necessary. If washed,
allow filter to completely dry before reinstalling. DO NOT operate
the unit without the filter.

3. Obstructed air flow. Maintain a minimum of 12 to 18" of clear air
space around the entire unit.

4. Cooling coils are dirty and need to be cleaned. Use warm water & dish washing liquid to
clean the coils. Rinse and wipe dry. Apply a light coating of WD40 to the coils.

5. Ambient air temperature at floor level is between 40 - 60 degrees.
dehumidifiers do not work well between those temperatures
(Unless, you have a Low Temp Unit). This applies mainly to
where the air temperature at floor level is colder than at shoulder level
in basement applications . Raising the unit up off the floor,
onto a sturdy table, counter top, etc, that can handle the weight
of the unit, plus a full tank of water, will usually resolve this
problem.

If none of the above solves the problem, it may be a case of the compressor needs to be recharged with refrigerant gas or that the humidity condenser sensor has failed. These things usually occur in units that are 5 years old or older. It's rare in a unit younger than that. But, it can happen. Parts are available, but recharging the compressor should be left to the pros.

If you decide to dispose of it. The land fill is not an option. The compressor has refrigerant gas in it and must be disposed of properly. Most cities and counties have drop off sites for this type of appliance.

I hope I was able to help you and thanks for choosing FixYa.

Aug 27, 2011 | DeLonghi DE500P Dehumidifier

1 Answer

The dehumidifier runs constantly and is not collecting water. We had it in the basement where it frosted up. Brought it upstairs where it ran and ran without collecting water. It was not like this last...


Sue, there are 5 basic, but solvable reason for what you described. Please pay particular attention to numbers 1 & 2.

1. The humidity extraction level is set to HIGH. Lower it to 32-35%.
2. Air intake filter is dirty or clogged. Turn unit OFF, & Unplug the
Unit, before removing to inspect & clean it, if necessary. If washed,
allow filter to completely dry before reinstalling. DO NOT operate
the unit without the filter.

3. Obstructed air flow. Maintain a minimum of 12 to 18" of clear air
space around the entire unit.

4. Cooling coils are dirty and need to be cleaned. Use warm water & dish washing liquid to
clean the coils. Rinse and wipe dry. Apply a light coating of WD40 to the coils.

5. Ambient air temperature at floor level is between 40 - 60 degrees.
dehumidifiers do not work well between those temperatures
(Unless, you have a Low Temp Unit). This applies mainly to
where the air temperature at floor level is colder than at shoulder
level
in basement applications. Raising the unit up off the floor,
onto a sturdy table, counter top, etc, that can handle the weight
of the unit, plus a full tank of water, will usually resolve this
problem.

If none of the above solves the problem, it may be a case of the compressor needs to be recharged with refrigerant gas or that the humidity condenser sensor has failed. These things usually occur in units that are 5 years old or older. It's rare in a unit younger than that. But, it can happen.

You also asked, "
do you know of a cradle to cradle product that lasts longer than this?". Unfortunately, I have no idea what you are talking about. Could you please explain? Thanks.

Jul 11, 2011 | GE AHG50LB / AHG50LD Dehumidifier

1 Answer

Dehumid. runs and fan blows but no water in tank and never shuts off, 5yr. old maytag, only runs in summer


Several things can cause this problem. The leading one, is that the humidity extraction level is set to high. Lower it to 35%. One of the others, is a dirty or clogged air intake filter. Followed by obstructed air flow. You need to maintain at least a minimum of 12" clear air space around the unit. Also, most humidifiers struggle to operate correctly, if the ambient air temperature at floor level is between 40 to 60 degrees F. This will also cause the fan to run a lot if the unit is set in continuous mode, rather than a timed mode. And finally, if any doors or windows are open, the unit will run forever. Make sure all doors and windows are closed.

Here's an in home test to see if it's working properly. Move the dehumidifier to the bathroom. Plug it in turn it ON and set the humidity/moisture extraction level to 35%. Turn the shower ON hot enough to generate steam. Do Not turn the bathroom exhaust fan ON and close any windows that may be open. As you exit the bathroom, close the door. Wait 15 to 20 minutes before returning to the bathroom. Once you do, turn the shower OFF and allow the unit to run for 5 minutes more. Then check the bucket for any signs of water. If you find some, the unit is working as it should.

If you don't see any signs of water, the unit's compressor may need to be recharged with refrigerant.

Hope this helped you to troubleshoot and solve the problem. Please let me know. Thanks.

May 29, 2011 | Maytag M7DH65B2A Dehumidifier

1 Answer

Haier dehumidifier will turn on but does not collect water.


hello. If your dehumidifier doesn't seem to run often but the humidity in the room is high, try adjusting the humidistat control on the dehumidifier to a dryer setting. If the dehumidifier seems to run constantly, but there's little or no water in the container, there may be a problem in the refrigeration system. Try cleaning the unit. If that doesn't work, you can't repair the refrigeration system yourself, you need a qualified appliance repair technician to do that.

Apr 14, 2010 | Haier HD656E Dehumidifier

2 Answers

I have an old Sahara 25 dehumidifier need water collector chamber


I contacted GE on the web and found out they don't make the parts anymore for this unit. I used Gorilla glue to repair the cracks in the old semi soft plastic water collector chamber.
dmbrownpe

Jan 29, 2010 | GE Dehumidifiers

1 Answer

I am having Daewoo refrigerator Model DIR220. When I switch on the refrigerator the compressor starts after about 3minuites and stops in few seconds. fan motor works continuously. As the compressor stops...


the compressor has an internal overload to protect it from overheating. the compressor is cooled by the refrigerant passing over it. It could be a bad compressor,, bad charge of refrigerant, or simply dirty coils not allowing air movement

Nov 26, 2009 | Dehumidifiers

1 Answer

Solenoid is not opening for water to ice maker


The only thing that controls the water valve on the IM side is the IM itself. If you can power up the water valve manually and it works fine then you need to take a look at the IM

Jun 10, 2009 | Goldstar DH504EL Dehumidifier

1 Answer

Hook up my 2 sub and my 2 amp


wire the subs at 2 ohm each. red to red and black to black and then to the amp. if thay are a dual 4 ohm sub. dual 2 ohms will need to be wired red to black on one coil and the other conected to the amp.

Apr 09, 2009 | Danby DDR601 Dehumidifier

1 Answer

Fan fixed but evaporator solenoid keeps activating at times


the purpose of the valve is to de-ice the evaporator and the valve is turned on by a timer usually. in normal operation, the evaporator builds up with ice (that is how water is extracted). when the valve operates, to put it simply, the hot gas is routed to the evaporator and hence melts the ice off

Aug 28, 2008 | Goldstar DH504EL Dehumidifier

Not finding what you are looking for?
Goldstar DH504EL Dehumidifier Logo

Related Topics:

1,329 people viewed this question

Ask a Question

Usually answered in minutes!

Top Goldstar Dehumidifiers Experts

Gil Shultz

Level 3 Expert

3368 Answers

Michael Youngman
Michael Youngman

Level 2 Expert

156 Answers

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1667 Answers

Are you a Goldstar Dehumidifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...