Question about Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

1 Answer

Roller on my dirt devil vision not spinning

I wondered if i need to replace the belt but cant figure out how to where it is or how to get to it

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How do you replace a belt no.5 on a dirt devil vision.

Posted on Apr 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

It stopped picking up dirt . I cleaned the filter, and the belt isn't broke on it. What do i do


Does the belt spin when you turn the vacuum on? There is likely hair wrapped around a brush or roller, or dirt clogged up inside the nozzle somewhere.

Jun 04, 2010 | Dirt Devil M086700 Vision Bagless Upright...

2 Answers

Brush does not spin


I thought my belt went bad....which it did, however there was another issue....The brush was not turning freeley, and would hardley turn at all, which caused my belt to go bad. Apparently, there are sealed bearings in the brush that you can not get to. If your brush will not turn, you can either spend some $$ and get a replacement. I opted to spend some time on mine, and soaked it in some Mr. Clean and water. I then sprayed brake part cleaner into both ends, and re soaked it. I then put some dish soap on either end and freed up the bearings. In between each of the steps I described above, I would try to work it by hand. I have not had a problem since, and saved some $$ too! Good luck and hope you get the same results I did;-)

Nov 08, 2009 | Dirt Devil Vision Turbo W/Bonus Upright...

1 Answer

My Dirt Devil ultra vision will not **** from base


Your belt is probably worn or broken. You need to replace the belt if you haven't recently. You can get the belts you need here:

Dirt Devil Ultra Vision Replacement Belts

Nov 07, 2009 | Vacuums

1 Answer

Belt pulley is broken


sad to say but as far as i know you cannot get any parts for dirt devil vacs only filters and belts and bags sorry 

Nov 03, 2009 | Dirt Devil Vision Turbo W/Bonus Upright...

1 Answer

Where is the belt on the dirt devil vision turbo cant find it


the belt is to the left of the brush. You need to revome the plastic covering (4 screws) to see it.

Oct 27, 2009 | Dirt Devil Vision Turbo W/Bonus Upright...

2 Answers

Replacement of the belt instructions


should be just 2 screws by the beater brush, bottom front of the machine, pop them out and remove brush to remove hairs etc. put new belt in .

Jun 15, 2009 | Dirt Devil Vision Turbo W/Bonus Upright...

2 Answers

Dirt Devil Vision bagless not working


Check the dirt cup filter. remove the dirt cup and check for proper suction. if you have good suction, check your belt

Jan 24, 2009 | Dirt Devil Featherlight Bagless Upright...

1 Answer

The belt is broken of my dirt devil


Remove brush roller and black caps at each end of the roller. Clean and oil the bearings.they must turn freely.

Dec 10, 2008 | Dirt Devil Vision Turbo W/Bonus Upright...

1 Answer

Missing part on motor shaft?


the reason the belts are burning up so quickly is the old rubber from the other belts is still on the motor shaft.clean the shaft down to the polished finish then put on a new belt.make sure your brush roller turns freely .thats the other possiblity.the brush roller might be bad.sometimes hair and dirt get twisted around the ends and keeps it from turning

Jun 28, 2008 | Dirt Devil M086700 Vision Bagless Upright...

Not finding what you are looking for?
Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum Logo

Related Topics:

237 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dirt Devil Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18297 Answers

Roger Potts

Level 3 Expert

694 Answers

Ryan S
Ryan S

Level 2 Expert

328 Answers

Are you a Dirt Devil Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...