Question about Sony FD Trinitron WEGA KV-32FS120 32" TV

1 Answer

Sony Trinitron approx 8 years old, no picture, no sound...

I don't have the exact model number but I know it's approximately 8 years old. It won't turn on, there is no picture, no sound but the standby/time light is blinking red, 4 times and then repeats. I tried unplugging it and re-plugging it and no change.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,071 Answers

That blinks and flashing have a diagnostic code;

Here is a list of the problems that might have occurred indicated by the number of blinks. The words in parentheses are those, which you will see for each of these faults on a diagnosis screen described later in this article.


  • Unit is dead, No blinks - Problem in the standby power section. Might check fuse, R607, Q601, IC601, R612 and VDR601 (should show open).
  • Continuous blink once a second, no pausing - No reply from the jungle IC301 (data bus is busy, shorted to ground, or held high), IK video path is defective.
  • One blink - not used for the self-diagnosis
  • Two blinks - B+ over current protection (OCP), unit goes to the standby mode then displays the 2 blink fault. Could be a short in the power supply of any of the circuits.
  • Three blinks - B+ over voltage protection (OVP), unit goes to the standby mode then displays the 3 blink fault. This is also a problem in the power supply circuit, check T603 and R672.
  • Four blinks - No vertical Deflection (V STOP), Screen goes to a single horizontal line then the video signal muted. Check IC1509, Q1505
  • Five blinks - AKB circuit (automatic kine bias), the timer/standby indicator blinks for about 30 seconds then goes to the self-diagnosis function. Something is wrong with the video. Check video out, Q705, 732, 761 and other components on the C board, also check Q218, 219, 220 on the A board. In addition, unit could be in IK blanking, try turning up screen slightly.
  • Six blinks - No Horizontal (H STOP), no raster, goes to the blinking self-diagnosis function immediately. Check C515 & 516 and the jungle IC, IC206.
  • Seven blinks - High voltage shutdown. The high voltage has exceeded 33k and the unit goes immediately into safety shutdown. Check power supply regulation and horizontal circuits.
  • Eight blinks - Problem with the audio (AUDIO), unit goes to standby and blinks the self-diagnosis code. Check IC406 audio amp, PS401, and 402. On some projection models of Sony TV sets, this code means that T8005 (flyback transformer), or the associative components in the high voltage circuits are defective on the D board.
  • Nine blinks - Replace D 6116 and D 6301 on the "G" board, do not resolder as this will fix the problem temporary. Or Panel Module Error or Thermal Error. If it is intermittent 9 blinks, meaning sometimes the TV comes on and other times you get flashing, then change the switching regulator on the "G" board or check connections. Make sure the regulator is -12 or -13 (negitive).
  • Ten blinks - Check Q8014 and Q8013 for shorts, leakage, or bad solder connections on the " D" board. If the transistors are bad, check R8051 and IC8005, also on the "D" board.
Intermittent problems? This is a great feature. You can also bring up these fault codes on-screen to see a list of the problem numbers with the abbreviation of the problem and the number of times this problem has occurred. This is slightly different than entering the service mode. To see the diagnostic screen, press the following buttons: Display, Channel, 5, volume Minus, ( not plus ) then Power. This brings up a screen with a list of the problems and number of times they have occurred. Each of the problems named, are abbreviated as, "OCP", "OVP", "V STOP", ETC. We have repeated them in parentheses in the text for the "Blinks" described above so you can correlate between the diagnostic screen and the blink codes.
Now that you know about these self-diagnostics, how do you use them? Say that you have a set with a black screen. You see that the LED is blinking four times. This would tell you that you have no vertical sweep, which is why the video is muted. If it was blinking 6 times, you would know that you have a horizontal fault. It's not a sure cure..
IMPORTANT: After you repair the unit, you MUST clear the values on this diagnostic screen. These codes do not reset themselves after the fault is corrected, so if you don't clear them, you'll be seeing "old" fault codes the next time you enter this screen. Clearing is done by going into the service mode (display, channel, 5, volume plus, then power ). Press 8 and Enter, which returns everything to the factory preset condition.

Hope it may help you;

Regards,
VOTIT

Posted on Jan 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Sony FD Trinitron 27' Model # KV-27FV310. It is approx 8 years old. After turning it on and watching a full screen for a few minutes; all of a sudden, a line came across half the screen;


top half missing is in vertical circuit of set---if it is a 27 inch and this old consider retiring it and replacing----other option is consider having a shop repair it--a rough guess would be as high as 150 dollars parts and labor is possible for your problems.

May 01, 2012 | Standard (CRT) Televisions

1 Answer

Sony trinitron, about 7 years old, turn it on and picture won't come on for about an hour


Check for bad connections on voltage regulator ic, or bad voltage reg ic in power supply.

Oct 23, 2011 | Sony FD Trinitron WEGA KV-32FS120 32" TV

1 Answer

My sony trinitron model kv-27S42 has no picture/sound, keeps clicking and the Stand by/Timer light keeps blinking. I have disconnected it for the night, plugged it back in but the problem remains? any...


Hello

Blinking of standby light in Sony TVs are fault indications. You just count the exact number of blinks occurs at a time after switch it ON. Switch it ON and OFF by its front panel power switch, and not by the remote control handset. Do this for at least four times, count the number of blinks, confirm and inform me. I can then locate the fault section of your Tv, seometimes even to the exact point of fault too. OK

Happy New Year

Dec 31, 2010 | Sony KV-27S42 27" TV

1 Answer

I have a Sony Trinitron 32" TV. The picture don't


Hello
Blinking of standby light in Sony sets are fault indications. You just count the number of blinks occur at a time, by switching the set ON-OFF by its front panel power switch, not by the remote control handset. Just do it for at least three or four times, count the exact number of blinks occurs there, and inform it to me through Fixya. Through the number of blinks, I can locate the faulty section, of somtimes to the exact fault location. Count it keenly and inform me. OK.

Dec 16, 2010 | Sony FD Trinitron WEGA KV-32FS120 32" TV

1 Answer

Is the sony trinitron 23 inch tv hd ready


You will need a model number before anyone can even do any research.
In general, there were never many CRT (picture tube) TVs made with the required ATSC tuner and if your set is 5+ years old, it isn't compatible with digital reception.

Oct 11, 2009 | Standard (CRT) Televisions

1 Answer

The color is fading in our KV-32FV26 Sony Wega The TV is approx 3 years old.


my sont tv model no. KV-XF21M83 (21 in's) indicator lamp flashes red a number of times between 3 secounds interval
the color of the tv has gone faded. The channels name on the top right or left side is not seen properly
The EHT is sparking near the picture tube.
Nessarry guidence may please be comnicated in this regard please. send me feed back to my email adress
sikandher@hotmail.com

Mar 13, 2009 | Sony FD Trinitron WEGA KV-32FS120 32" TV

2 Answers

TV will not come on.


The 7 blinks indicate a high voltage shutdown (high voltage exceeded 33,000V). This is usually caused by a defective regulator. Could you please post the exact model number (KVxxx) and I'll look up the part you will likely need?

Thanks,
Dan

Jul 28, 2008 | Sony FD Trinitron WEGA KV-20FS120 20" TV

1 Answer

Sony Trinitron 29inch Color TV


The 2 blinks are an indication of over-current. This is usually because of a shorted component. The most common is the horizontal output transistor. This will be a 3-legged part attached to a heat sink close to the flyback transformer (part with red wire coming out the top). This transistor will be marked C4856 or something similar. Update this with the exact marking and I'll provide you with the full part number and approximate cost.

Dan

Jul 14, 2008 | Sony FD Trinitron WEGA KV-29LS35 29" TV

2 Answers

Sony Trinitron 32" TV will not come on and stand-by light blinks


It cant hurt to try...

While I was reading some other post about this problem, one guy said to try using a hairdryer on the right side of the TV1.gif for a few minutes to dry out humidity, becuse the trinitron has some kind of feature that causes it to 'protect itself' when too much humidity is in the air.
Hmmmmm sounded silly, but we had nothing to lose and tried it.
Lo and behold, our TV is back on.

Dec 31, 2007 | Sony FD Trinitron WEGA KV-32FS120 32" TV

Not finding what you are looking for?
Sony FD Trinitron WEGA KV-32FS120 32" TV Logo

1,049 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Standard (CRT) Televisions Experts

The Knight
The Knight

Level 3 Expert

68368 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

Are you a Sony Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...