Question about Panduit LS7 THERMA TRANS Thermal Label Printer

1 Answer

Repair parts Where can I get replacement gears for the LS7

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Dude, at the cost of the unit - you can get a new one - I've got several new one!

Posted on May 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

The power take off for accessories doesn't work


That's a bit of a task to sort out. If you aren't up for a full strip down and clean up followed by new gears and repack with grease then contact Kitchen Aid for a local repairer. You will be up for a couple of gears and maybe even the top housing if the bush for the accessory drive gear is wrecked. If you need "how to" help then get back to me for step by step.

Apr 04, 2015 | KitchenAid K45SS Classic Stand Mixer

1 Answer

What turns the speed sensor in tranny 2004 isuzu.rodeo 3.5 Can it be repaired without replacing the transmision?


it is driven by a drive gear on the output shaft of the transmission. you could have a bad driven gear that is the gear that is driven to create the electrical pulses to show a speed. the drive gear on some transmissions are part of the output shaft and some gears are replaceable without replacing the output shaft. in either case a part can be replaced without replacing the complete transmission.

Sep 29, 2014 | 2004 Isuzu Rodeo

1 Answer

How do I know if a engine is a LS7 454


It's not - they never made it into production.

Jul 19, 2014 | Engines & Components for Chevrolet Chevy

1 Answer

2001 gmc senoma not shifting into 4h


Gear out alignments and worn out gears parts most likely the caused,must be check out and replaces gears parts by those transmission professional like in AMCO,Many,Moe and Jack for transmission repair and replacement of parts

Sep 04, 2013 | Cars & Trucks

1 Answer

Where can I get LS7-75NL-1 label tape?


I am also looking for a tape cassette (LS7-38-1) for the LS7 label printer, and cannot find one anywhere. I called Panduit and they said the LS7 has been obsolete for several years, and they have no tape cassettes for it.

Feb 18, 2013 | Panduit LS7 THERMA TRANS Thermal Label...

1 Answer

Abit ls7 v2


be more specific.

Jul 15, 2012 | Computers & Internet

2 Answers

Reverse Gear does not work, Can this be repaired ? or replaced? So I do not use reverse.


This is very common, the reverse gears blows out, the reverse gear and some bushings need replacing, many trany shops wont do it, they rather sell you another trany, we had a retired vw tech that would repair them for us all you did was remove the trany, but anyway it can be repaired the parts cost about 150.00 then the rest is labor,

Sep 18, 2010 | 2003 Volkswagen Jetta TDI

2 Answers

What engines can replace the rotery engine in my 1987 mazda rx7? Looking for something with cyliders over a rotery engine, also with more power. Any sugustions?


Well the most common swaps are putting in Small block ford's and Chevy's. The one I see mostly is the 5.0 Mustang motor swap. There are numerous kits for motor mounts and relocation brackets that make it a fairly straight forward swap. Do a little research and you will start seeing quite a few results that will answer your questions on How to's and so forth.

Sep 15, 2010 | 1987 Mazda RX-7

1 Answer

On a NEC RC-28D multiplexer I have a error on a low speed card that displays "LS7 IN1". What is this?


That DS1 is down. This would be number 1 in card 7. You can either turn up the circuit, or flip the 'IN USE' jumper off for that port on the card.

Jul 09, 2008 | NEC Lands Phones

Not finding what you are looking for?
Panduit LS7 THERMA TRANS Thermal Label Printer Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panduit Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

k24674

Level 3 Expert

7993 Answers

yadayada
yadayada

Level 3 Expert

70387 Answers

Are you a Panduit Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...