Question about Mitsubishi VS-50607 50" Rear Projection Television

Open Question

Does anyone have a schematic for a d'link di-614+ router

All I need is the value of f1 and zener diode 1

Thanks in advance,

srich

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Password protect wireless access


You'll need to access the administrator web page for your router, and then set a security key (password) for wireless users.

For step-by-step instructions for setting up security on the D-Link DI-614 router, see:

http://technicallyeasy.net/2010/10/how-to-secure-d-link-di-614-wireless-router/

Sep 04, 2012 | D-Link 2.4GHz Wireless Router DI-614

1 Answer

Unable to write network settings to device error code 0x8004d112


1. this error is not recognizable.
But here is the D-link site for updating your firmware for the DI-614
this may resolve your issue.
http://www.dlink.com/products/?pid=DI-614%2b
2. You also may want to check the status of you router by logging into it and checking the "status" page (192.168.0.1)
User : admin
No password unless specified
This will tell you a lot as to what the router is doing and not doing.

Jun 18, 2010 | D-Link AirPlus DI-614+ Wireless Router

1 Answer

Setting up firewall


Go to this link
The advanced category has all the configs to the router
So read it
Thanks
Good Luck
:)
Please rate the answer if it helps u

Jun 11, 2009 | D-Link AirPlus DI-614+ Wireless Router

1 Answer

Burnt Zener diode... Voltage spec??


On the cathode of the zener diode look for a filter cap and check its value the voltage of the zener should be less than the working voltage of the zener. Basicly its likely being used as a shunt regulator as protection and regulation of the voltage. When the zener hits a certain threshold it will breakdown and start conducting to ground until the supply regulates and then it will recover. If the filter cap for that voltage rail was 25V I would guess that the zener would probably be regulating between 12 and 20 volts. I'd pick a 15V Zener its probably +- %10 on the original and any system should be able to take a %10 tolerance as a general design rule.

May 07, 2009 | Emerson Televison & Video

3 Answers

UNKNOWN VALUE OF VOLTAGE ZENER DIODES


I was not able to find any service or schematic for this model. The colors means that the value is 22.6 volts zener diode with the other blue band indicating where the cathode is.
Could you tell me where or what other components this zener diode is connected to?

Jul 02, 2008 | Televison & Video

1 Answer

Motherboard Schematic


happened to me, just put a straithrough wire or bridge it and dont plug your modems power supply in next time =!

Jun 28, 2008 | Buffalo Technology AirStation G54...

3 Answers

Require value of D5


TomTom One uses a Linear Technologies chip LTC3455 as a USB/charger power controller. See http://cds.linear.com/docs/Datasheet/3455fc.pdf. This chip is susceptible to high transient voltages that result from resonances created by parasitic inductances and capacitances of the USB/in-car charger cable . Good designs using this chip suggest that a 1 ohm resistance be put in the path of the cable to reduce the Q of the resonance and hence transient voltages. A 6V Zener diode D5 also serves to protect the chip from these transients.
If the Zener diode is blown it is most likely the the LTC3455 chip is gone as well. You can replace the chip which costs £5.00 (located in the shielded portion of the PCB). The recommended Zener Diodes for this chip are either the EDZ5.6B or EDZ6.2B manufactured by ROHM (http://www.rohm.com/products/databook/di/pdf/edz5.6b.pdf or http://www.rohm.com/products/databook/di/pdf/edz6.2b.pdf). These can be used to replace D5. The STMicroeletronics SM2T6V8A can also be used to replace D5 (http://www.st.com/stonline/products/literature/ds/8694/sm2t.pdf). All the Zeners cost a modest £0.22. I hope this is helpful.
Emmanuel Zyambo

Jun 15, 2008 | Tomtom One XL GPS Receiver

1 Answer

D-Link 614 Plus


You need to do some reconfiguration on your router by using the setup cd or by manually configuring it using the user interface of the router.

Apr 05, 2008 | D-Link DI 514 Wireless Router (DI-514)

2 Answers

DI-524 wireless router as wireless switch


You need to disable the DHCP server on your "slave" wireless router ( the di-524 ). In D-link routers this might be called configuring it to be an "Access point".

When this happens, connecting to the second wireless router should cause your computer to obtain an IP address which is in the range of the first router (that is to say, it will use the first router's dhcp server).

You should be able have your laptop connect with an automatic IP address and have it work.

Jan 24, 2008 | D-Link AirPlus DI-524 Wireless Router

Not finding what you are looking for?
Mitsubishi VS-50607 50" Rear Projection Television Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1213 Answers

The Knight
The Knight

Level 3 Expert

74473 Answers

Jaime Hernandez

Level 3 Expert

2318 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...