Question about Electronic Keyless Locks

3 Answers

I have a skylink 318r keypad with receiver to open my overhead door but dont know code as sellers of the home didn't leave this with - how do you reprogram both transitter and receiver?

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Keypad is model 318K
receiver is model 318R
factory setting for keypad PIN is 0000 #
there is no master reset code
you must have the current code to reset the PIN
if you hit the correct code on the keypad followed by the # key - you will get three beeps.
to change the PIN: (current PIN needed)
enter current 4 digit PIN then *
enter new 4 digit PIN followed by *
reenter new 4 digit pin and *
if accepted - backlight will flash and will sound one long beep
takes 2 CR2032 button cells for keypad
you could sit in a chair one night and start at 0000# then 0001# etc until you get three beeps
then use above procedure to change to your desired code
good luck

Posted on Mar 25, 2010

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Push the button on the side of the receiver, then push the button on the remote. That should program the receiver to accept the transmitter. To unprogram all the old transmitters, hold down the button on the side of the receiver until it starts flashing quickly-about 10 seconds.Then program the new one as above. (if this were the old dip switch type, you'd open up the receiver box to read/set the switches)

Posted on Sep 13, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

You might want to look inside the box (can't think of the name that lifts the garage door). it may be written there or be obvious by switches.

Robert

Posted on Jan 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I came home last night and when i enetered in the code to the door, a green light came on in the back of the unit, a noise alarmed and the door did not open. Does that mean that the battery needs to be...


I just had this problem with a model 909. The batteries might be too weak to move the bolt. See if it will move with the door open. Unfortunately, if it's more than a year old, it's out of warranty and no parts are available to repair the electronics. I replaced mine with a different brand, which doesn't drive the bolt, it simply enables the bolt to be moved by hand.

Aug 10, 2011 | Kwikset 907 907-15 Satin Nickel Powerbolt...

1 Answer

My keypad won't light up when door is locked whe you push lock won't light up green


To make the keys light up when you want to enter your code, you have to push the lock button on the keypad first. If the keypad light never comes on, open the door and manually lock the interior lock, then press the keypad lock button. The above instructions should then work.

Good luck--and please provide feedback if this helps!

Aug 04, 2011 | Kwikset 909 909-L03 Lifetime Polished...

1 Answer

How do i change the code on a s25e digital safe i cant find the book


if its like my old woolworths one, open the door and press a red reset button on the inside of the door, close the door and dont lock, put in the 4 numbers u wish a press a A button on the keypad, or whatever ur enter button is, then lock it, then press the 4 numbers again and the A button or enter, a light should stay on and unlock :)

Feb 21, 2011 | Safe International Electronic Gun Safe...

1 Answer

I need to change the combo for my fe595 and dont know how. the serial number is 715739 andthe user codes are: A 6152 and B 1514. How do I reprogram the combination?


How can I program my electronic keypad lock when the instructions with the programming code have been lost?The back plate of the keypad side of the lock on the exterior of the door has a sticker which includes the serial number, six digit programming code and two pre-programmed four digit user codes. The lock must be disassembled to a point the exterior of the lock can be pulled away from the door and the information on the sticker made note of.

This link will give you instructions for various models of Schlage locks:
http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx

Good luck!

Feb 06, 2011 | Schlage Electronic Lock FE595 Plymouth or...

1 Answer

Need to reset code. i know the cod now .just dont know how to enter new one


There's a video link on this page, under the FE 595 header:

http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx

Good luck!

Feb 05, 2011 | Schlage FE595VCAM716ACC Camelot Keypad...

1 Answer

Hi, I have recently moved into a new home with the Schlage BE365VCAM619 Camelot Deadbolt Keypad, Satin Nickel installed in the front door. We weren't left with any manuals or anything and have no idea how...


How can I program my electronic keypad lock when the instructions with the programming code have been lost?The back plate of the keypad side of the lock on the exterior of the door has a sticker which includes the serial number, six digit programming code and two pre-programmed four digit user codes. The lock must be disassembled to a point the exterior of the lock can be pulled away from the door and the information on the sticker made note of.

This link will give you instructions for various models of Schlage locks:
http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx
There is a video on this page, showing how to change codes.

Good luck!

Jan 10, 2011 | Schlage Camelot Deadbolt Keypad, Satin...

1 Answer

The number illumination has gone out. How to fix?


My keypad won't light up when door is locked when you push lock won't light up green:

To make the keys light up when you want to enter your code, you have to push the lock button on the keypad first. If the keypad light never comes on, open the door and manually lock the interior lock, then press the keypad lock button. The above instructions should then work.

Jan 07, 2011 | Schlage BE365-PLY BE365PLY626 Satin...

1 Answer

I want to know if a universal wireless touchpad can be added to a Stanley Quiet Glide Garage Door Opener? If so, how do you set it up, I did not see any smart button or dip switches?


Hi - did you have any luck? I just bought a Skylink universal remote from Cdn Tire and don't see the "smart" button or dip switches on my Stanley remote or motor casing. There is a learn button on the casing but that appears to be for the door to "learn" the proper setting to go up and down and has nothing to do with the remote. Thanks!

Dec 20, 2010 | Electronic Keyless Locks

6 Answers

I forgot the safewell electronic code and didnt have the key


NOTE: The safe needs to be upright and right side up or the locking mechanism
won’t work.
ELECTRONIC SAFES
To open an electronic safe the first time, press the following numbers/letters on the
electronic keypad –159B. (These numbers are preset. You should change the code as soon
as possible after opening the safe to insure proper security). After you have entered the
factory set code, you will need to turn the knob on the faceplate to open the door. You will
have 5 seconds to turn the knob before the locking mechanism is reactivated.
ENTERING YOUR SECURITY CODE
To enter your own security code you will need to follow the steps listed below:
1. After opening the electronic safe (with the pre -set factory code of 159B) locate the
small red button on the inside of the door near the hinge.
2. Press the red button and then release it, you will hear a beep.
DO NOT SHUT THE DOOR UNTIL YOU HAVE CONFIRMED THAT YOUR NEW
SECURITY CODE HAS BEEN ENTERED CORRECTLY.
3. With the door open, enter your own personal security code, which can be 3- 8 digits
long, and confirm your new code by pressing the letter “B” on the electronic touch pad.
Before you close the door, try the new security code to make sure the lock release the
knob so you can turn it and retract the live action locking bolts.

If you can not get this open more then likely you will have to cut it open.. One last thing to try is to email safewell sales@safewellsafe.com
\
Good luck

Sep 14, 2009 | Electronic Keyless Locks

Not finding what you are looking for?
Electronic Keyless Locks Logo

Related Topics:

1,120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Electronic Keyless Locks Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Jim Goldsmith
Jim Goldsmith

Level 3 Expert

1869 Answers

john h

Level 3 Expert

7192 Answers

Are you an Electronic Keyless Lock Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...