Question about Samsung HLN5065W 50" Rear Projection HDTV-Ready Television

2 Answers

Samsung hl61750a - unable to display video service over hdmi

Just purchased a Samsung hl61a750; have at&t uverse: connected via hdmi cable; displayed msg 'mode not supported' ; switched to alternate input source via s-video and audio component cables to watch tv; msg appeared at top of screen 'unable to display video service over hdmi. hdcp link integrity check failed (h1005)'

Any suggestions to solve this problem will be greatly appreciated!!!

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I was using an hdmi cable purchased online. A friend told me that it might be the 'cheap' hdmi cable. I tried a set of Monster hdmi cables and problem solved. So all hdmi cables are not the same.

Posted on Jan 31, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Restart the att cable box by unplugging the power cord.

Posted on Jul 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am unable to get a picture on hdmi when i connect my ps3, but am able to get sound when i use ps3 controller. any ideas ?


Steps
  1. Step 1 Check for an HDMI port Check the back of your television for an HDMI port and refer to your owner's manual for your television's resolution. A resolution of 1080p offers the highest quality.
  2. Most PS3 systems support 1.3 HDMI, but older systems may need a software update from the 1.1 or 1.2 version.
  3. Step 2 Disconnect cables Disconnect all the cables and adapters from the back of your PS3, and then unplug your TV to reduce the risk of shock as you work.
  4. Step 3 Connect HDMI cable Connect the HDMI cable. Reconnect the power cables on both the TV and the PS3 system.
  5. Step 4 Hold power button Hold down the power button until the PS3 beeps and continue holding it for an additional five seconds until the system makes a second beep.
  6. The Playstation 3 should detect the high definition cable and automatically adjust the settings to give you the best picture and sound possible.
  7. Step 5 Test the connection Test the connection. If the HDMI cable isn't working, turn everything off and reconnect the original cables to manually change the settings.
  8. Step 6 Adjust the settings Turn the system back on, select Settings, Display Settings, Video Output Settings, and then HDMI. Repeat the process for your Audio Settings. You can now experience your games with the highest video and audio quality available.

Dec 01, 2014 | Sony KDF-E50A12U 50" LCD HDTV

1 Answer

I have a Nikon D50 DSLR. I want to connect my camera with a HDMI cable to display my photos. What cable do I use and where do I plug it in?


The D50 only has an Analogue Video Out on it it does NOT have a HDMI Cable outlet like some of the newer Nikon Cameras like the D 300 or D300s for example. So you can only plug the camera into your television via the supplied Video cable (with yellow end). The small mini jack end goes into the left side of the camera under the rubberized flap and the larger end goes into a standard RCA Jack for video in on your TV set.

Refer to page 58 of the user manual for diagrams and more detail.

Jun 11, 2009 | Hitachi 57F500 57" Rear Projection...

2 Answers

HDMI PORT STOPPED WORKING!!


the best option here is connect via a standard PS2 avi cable or componet cable until your tech guy comes out!

Apr 30, 2009 | Projection Televisions

1 Answer

Mitsu 57731 problems have wide bar across screen


This is an ongoing problem with Mitsubishi DLP HDTV's contact the Customer Service at 1-800-332-211. Tell them this has been going on for a while and you want the TV either Fixed or Replaced. Ask for Adrianne Hardt, she is a Customer Service Manager...... TELL HER RICK GRIFFITH told you to call.

I am in the 4th week negociations with Mitsubishi over these exact problems. I purchased my 57" DLP HDTV in Aug of 06. Replaced the Lamp 3 times and have had 5 Service calls. I DO NOT have and extended Warranty. Mitsubishi provided me with the extention in writing and stated if any problem occurred again they would replace the Unit or provided monetary compensation.

Good Luck and be persistant.

Any of you can email me for from info and covette54@live.com

Feb 23, 2009 | Mitsubishi WD-57731 57" Projection HDTV

1 Answer

Samsung DLP 56' TV turns itself off when I initially turn it own. (I turn it on, then it shuts off for approximately 5-10 seconds and turns back on. Sometimes it does it a couple of times before it stays...


The problem is with the ATT UVERSE HDTV BOX and not the Samsung DLP TV. There is an inherent problem with the ATT UVERSE HDTV Box when using a HDMI cable. This was verified by the ATT UVERSE Technician.

Thanks,

Dec 13, 2008 | Projection Televisions

1 Answer

Bought a samsung lcd tv 450.. .need to use it as a monitor for my computer.. how do you set it up so it pulls up windows...


After connecting the TV to the computer using S-Video or HDMI cable, right click on your desktop and go to Graphic option or teh Nvidea control panel. From there select your TV which will be displayed in the window. You will get the display in your lcd TV. Let me know if it resolved because I also use the same connection at my home.

Thanks

Oct 17, 2008 | Samsung Projection Televisions

1 Answer

HD 1080p TV


Hey peterman,

Depending on the TV model that you purchased, you may have four to five different options that you can use to make the necessary connections for your home theater: composite, component, S-video, DVI and HDMI cabling.

Composite cabling may often be considered to be the "lowest quality" type of cable that you can use to connect two devices in your home theater, and generally consists of three color-coded cables: one yellow, one red and one white. While the yellow cable is typically used to transmit the video signal to your TV, the red and white cables transmit the right and left audio channels respectively. Composite video is somewhat limited in the fact that it is primarily intended for use with analog TV sets - by using composite cabling you may limit the quality of picture your HDTV is able to display.

Analog component cabling then can be viewed as a “step up” from composite cabling. Rather than transmitting video information over a single cable, component cabling instead uses three. Each of these cables transmits a different portion of a video image, and can often be found in bundles with one red, one green and one blue cable. Please keep in mind that component cabling still requires the use of a secondary cable to carry an audio signal, which may need to be purchased separately.

The primary benefit of using component over composite cabling is that many users may report a cleaner, more brilliant image on their TV as a result. This is not a guarantee however, as picture quality is often based as much on personal preference as it is the actual configuration and settings of the equipment used.

Often considered “in-between” composite and component cabling is S-video. Like component video, S-video cables split the information sent to your TV into multiple analog signals…two signals, to be precise. Unlike component video however, these two separate signals are sent using the same cable. Again, when using this type of connection a separate cable for audio signals is necessary.

DVI cabling is the first truly digital option available to most consumers. While it only carries a video signal (like its analog counterparts), DVI cabling can frequently be found connecting computers to monitors or digital projectors. These types of cables will have a unique shape that prevents them from being used as anything other than a video connection, and were designed to optimize signals transmitted from external devices to a visual display.

HDMI on the other hand, is another widely available digital alternative. Unlike DVI, HDMI cables support both video and audio signals, allowing consumers to avoid the proverbial “rat’s nest” behind a home theater system that one might encounter when using multiple cables.

Because HDMI cabling was developed to be backwards compatible with DVI, HDMI and DVI connections may often be able to be used interchangeably using special adaptors. Essentially, if your HD receiver/Blu-ray player only has DVI outputs and your HDTV only has HDMI inputs, you may still be able to connect those devices to your HDTV using the proper accessories.

While some major retailers may recommend using HDMI cables first and foremost over the other alternatives, this does not necessarily always make them the best choice to use. The quality of an image displayed on an HDTV will always be dependent as much on the TV itself, as it is on personal preference and other external devices. Yes, the type of cables used does play a part, but they should never be treated as the only factor to consider when setting up your home theater.

Should you have any questions or lingering doubts, I would strongly suggest speaking with a Magnolia Home Theater agent at your local Best Buy™ store for more information. Most stores will have similar TV's on display using more than one type of connection, and sales associates are always able to provide additional suggestions if desired.

Hope this helps you out.

Sincerely,
Aaron
Go Ahead. Use Us.

Jun 24, 2008 | Projection Televisions

1 Answer

I am trying to connect my Samsung DVD Recorder to my Samsung PS-42D7HD tv via the HDMI cable but it just comes up "no signal" on the tv - nothing at all. Also have an Olin HD Set top box with...


Hello

by befault your dvd recorder is transmiting signals via component video, so what you need to do is this connect both cable HDMI and Component or just a video cable then go into setup and then select video out via HDMI your video will go off on the screen and then with TV remote slect input source HDMI on TV and it should work fine.

Thankyou

May 09, 2008 | Projection Televisions

1 Answer

1080p high def issues


The HDMI cable I had originally wasn't a good enough quality. I purchased an HDMI v1.3 cable and everything works at 1080p. You don't need to pay loads for a cable, got mine from Play for £9.99.

Mar 29, 2008 | Projection Televisions

1 Answer

HDMI to DVI UPSCALING Problem


The Digital Visual Interface (DVI) is a video interface standard designed to maximize the visual quality of digital display devices such as flat panel LCD computer displays and digital projectors. It was developed by an industry consortium, the Digital Display Working Group (DDWG). It is designed primarily for carrying uncompressed digital video data to a display. It is partially compatible with the HDMI standard in digital mode (DVI-D). So yes it should work fine

Jun 04, 2007 | Mitsubishi WS-55613 55" Rear Projection...

Not finding what you are looking for?
Samsung HLN5065W 50" Rear Projection HDTV-Ready Television Logo

1,487 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Projection Televisions Experts

The Wyzzyrd

Level 2 Expert

83 Answers

Donald Griswold
Donald Griswold

Level 1 Expert

8 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

Are you a Samsung Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...