Question about 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

4 Answers

VIPER 5701 remote how tofix?

Hi, I was in the store and must have hit some buttons on the two way remote by mistake. Now when I push any button nothing works and I get a red light and a buzzing sound, but my spare one way remote works anybody have any ideas how to reset my 2 way remote so it will work?. I called VIPERS support and waited 1 hour on hold and finally hung up. This companys support SUCKS!!!! Also Vipers support recorded message says I have a CRASH CARD in my box and I don`t see and crash card can someone PLEASE tell me what it is. Thanks,,,,,,PJ

Posted by on

  • zroseheim Feb 03, 2009

    My Viper 5701 2-way remote start went bad about a month ago, I had the whole thing replaced under the warranty. Now it has started doing it again, the blue light on the receiver is no longer flashing, and no buttons work. If I take the batteries out of the remote, then put them back in, all functions work for about a minute.

×

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

You have the key pad lock turned on. It protects the keys from unwanted pressing when in your pocket. To unlock you hit the F key then the unlock key, you can now use any command untill you let it set for 60 seconds, then it locks again.

to stop this totally, u hold down the F key for 12 seconds it will beep and top light turns orange, then hold down the unlock key for 2 seconds, it beeps then u hit the lock key to turn off this feature (top green light goes out). then hold F down, and F down again, should b good to go!

REM

Posted on Jul 14, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Take it out of valet mode maybe? it worked with mine......

hope it helps

Posted on Jan 07, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Directed will be shipping out new brians in the next few months with a firmware update that resolves this issue completely. Depending on where it was purchased, I would believe most retailers will do a swap for you when those are shipped and become available. In the meantime there is a fix. Place a 10,000 ohm resistor in series with the blue wire on the antenna lead as close to the brain as possible. Hope this helps!

Posted on May 16, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Try removing the 15 amp fuse on the red wire going to the alarm brain for a few minutes.  Then reinstall the fuse.  I have the Clifford version of this alarm/remote start and had to do this a couple of times.  Not sure what DEI recommends as I installed mine myself and DEI won't give any support.  As far as a crash card you don't need it you just have to wait forever on hold and they will troubleshoot it by model number.  But they will just tell you to take it to your nearest dealer and have them check it out.

Posted on Mar 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why won't it start vehicle?


[PDF]Responder LE Model 5701 Security and Remote Start ...

xtremetruck.net/file/1101-Viper+5701+Owner's+Guide.pdf
the year, make and model of the vehicle; vehicle license number and vehicleidentification number. All ..... One five-button/2-way Supercode Responder LE RemoteControl. ? .... Disarm. Unlock LED blink for one second with 2 Beeps. Remote. Start..... Long-time Viper system users will notice the following differences:.

Viper LED 2-Way Security + Remote Start System

https://www.viper.com/car/securityremotestart/.../viper-led-2-way-securit...
Viper's elegant new Responder LE transceivers mark a giant leap forward in 21st century vehicle security and remote start, and an evolutionary milestone for the ...

Viper 5901 remote start error fix - YouTube

? 2:38
https://www.youtube.com/watch?v=wsSorAf88nw
Jan 13, 2013 - Uploaded by Power2ThePeopleZ
5901 won't start vehicle; gives an error. ... or even try to open the hood. the door remains locked when you start the car with theviper alarm.

Help With Programming/Pairing Viper Remote - YouTube

? 2:49
https://www.youtube.com/watch?v=cgbQsZuVyt8
Dec 2, 2010 - Uploaded by Paul L
I have a two-way remote from my Viper 5901 system. ... The other car (one in video) has the Viper 5701 system in it. .... and then release 3) press the remote start button 2 times until pairremote is displayed 4)press and old ... I had the same problem that the remote won't pair with the system no matter what.

15964701 Viper 5701 2 way alarm w/ remote start won't




Jan 05, 2016 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

1 Answer

HOW TO FIND THE VALET SWITCH IN A 2000 DODGE STRATUS


The valet button on the Viper 5701 is located on the antenna which is normally installed on the front windshield. Viper calls this button the "control button".
Here is a link to the owner's guide:

http://www.directeddealers.com/manuals/OG/Viper/G5202V%202011-03%20web2.pdf

Feb 20, 2013 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

1 Answer

Remote start wont start the car


try hitting function twice so its at level 2 code and hit the unlock button, that sends it into remote valet mode. if that isnt it make sure the valet toggle switch is on and connected

Dec 01, 2012 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

2 Answers

Lost my remote viper remote starter. Car alarm goes off when open and car won't start. What do i do to disarm the alarm since the car won't start?


Common issue.
Open doorAlarm will be going offLocate the antenna (should be on the windshield)Find the little black push button on the antenna.Turn key to the ON/IGN position (where all lights are on)WITHIN 5 SECONDS push the black button 1 time and release (unless your installer changed the number of pushes it should be 1)Within seconds the alarm will ceaseStart your vehicle.


If any other issues, send me a message.

Aug 25, 2011 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

1 Answer

I am trying to disarm the viper 5701 2 way alarm w/ remote start and the keypad nor is the manual override responding. How can I disable the alarm?


Get in car........alarm will be going offVisually find the black valet button..........it should be next to led on the antennaTurn key to IGN position...........so all dash lights are onWithin 5 seconds push the valet button 1 time..............may have been programmed to more times, but ussually notSiren should stop and you can start the car.
TO put into valet mode
Key to IGNKey to OFFPush valet button 1 time.Led should now be solid.

Jul 09, 2011 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

1 Answer

The alarm is on a 1996 f150 the alarm will not chirp the led on truck is solid it isnt blinking and it is a 5701 viper


Your alarm got put into valet mode some how
.It's easy to reverse out of it back to normal. First look for a small black push button under the dash somewhere. It's called a valet button. Here are the steps.
1. open door
2.turn key on then off
3.then within 10 seconds hit that valet button once(your alarm light should be off. Tell you arm it again. Then it will blink)
Hope this helps

Aug 18, 2010 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

1 Answer

How to program viper 5701 remote


Unlock doors
Push and hold f button for 8-10 seconds until amber light is on solid
Push Remote start button for about 4 seconds till amber light flashes 3 times
Put key in to IGN position
Push valet (black button) one time and release
Push and hold valet button
Push either lock or unlock on viper remote
Key out of IGN
Test unit
The horn or siren may sound afterwards to indicate SUCCESS!!!!!!

Nov 21, 2009 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

2 Answers

How do I lock my keypad


there is a way to do it in the manual which can be found at www.viper.com/support.... i did it by mistake and now can't figure out how to turn it off

Apr 01, 2009 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

1 Answer

Problem with my viper alarm system on my 98' odyssey


first, you need to manuslly disarm the alarm. open driver's door, put key in ignition, turn on ignition, an then within 10 seconds push the valet/program button for a couple of seconds. (it is the little spring loaded push button that they installed with your system. probably in the kick panel or under dash

Dec 28, 2008 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

Not finding what you are looking for?
5701 VIPER 5701 2-WAY ALARM w/REMOTE START Logo

3,468 people viewed this question

Ask a Question

Usually answered in minutes!

Top Viper Vehicle Parts & Accessories Experts

Tre Elkins

Level 3 Expert

643 Answers

Shehu Pro
Shehu Pro

Level 3 Expert

1284 Answers

Joseph Gallucci

Level 2 Expert

120 Answers

Are you a Viper Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...