Question about Hotpoint Ultima WF860 Front Load Washer

1 Answer

Hotpopint Washing Machine WT741 flashing F-12

Flashing F - 12

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 1 Answer

Resolved the problem.
Switched off the power to the machine. hit the on /off button and the f-12 error code disappeared .
On reappling the power to the machine the orignial programme continued to completionj

Posted on Jan 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My door is shut and light is on flashing door on my hotpoint washing machine WT741. the door is shut and it does lock aswel so why the flashing light and no washing being done?


Hi from retired Englishman in SW France,
There is likely to be a problem with the 'door closed' sensor/microswitch requiring a service engineer's attention I suggest ;-0(

If this has assisted and/or clarified the situation for you please consider a 4 thumbs up on our rating.
Thanks and good luck!
John C

May 07, 2011 | Hotpoint Aquarius WD63 Front Load...

1 Answer

My hotpoint washing machine wt741 will do nothing except fast spin, LED display is flashing TEST, it will not stop doing this unless i switch if off, what can i do?


Hi,
To get out of it you need to press start, the display should go daft. Press start again and the display should settle down. Now press the on/off button and the start button at the same time and hold them down for a few seconds until the display shows d-end or d-off.
Your machine should now work.

Unplug your appliance before working on it

Thank You

Sep 12, 2010 | Hotpoint Aquarius WMA42 Front Load Washer

1 Answer

Hotpoint ultima WT741 washing machine not working flashing F-03


F03 - Wash thermistor open/short circuit need a engineer out to fix it. hope this helps.

Mar 27, 2010 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Hotpoint WT741. When power on and 'on' button pressed ALL display lights flash continuously. Sometimes after 2-3 hours they stop and a wash program can be used, but then machine reverts to all light...


Have had this problem on our Hotpoint WT741 washing machine. Fixed it this evening as far as I can tell. Seems it was a loose connection. Took the top off the machine and checked the ribbon connection to the display board at the top front. First, I removed the board (is held in by plastic clips - remove the programme selector knob first) and inspected to see it was okay then refitted it, making sure that the ribbon cable was pushed firmly onto the board. I then removed the rear access panel around the drain hose and checked the connections onto board at the bottom rear of the machine. I gave each connection a good push to check they were properly seated. Having done this, I have been unable to reproduce the fault with repeated switching off/on of the machine. It now appears to be working fine. I suspect the fault arises as a consequence of vibrations from the machine during operation causing one or more connectors to work loose - probably the ribbon cable on the front panel. So the problem should be rectified by checking these are properly seated. If you know what you are doing it's a simple job. Make sure you unplug the machine before accessing the machine and turn off the water supply. Don't attempt this if you aren't sure what you are doing and aren't confident with electronics.

Oct 24, 2009 | Washing Machines

1 Answer

My hotpoint washing machine wt741 wont stop flashing


Hi Donna, did you fix this? Am guessing you have by now one way or another but have posted a suggested solution for someone else: http://www.fixya.com/support/t3268817-hotpoint_wt741_when_power_button. Worked for myself and one other poster on here.

Jun 23, 2009 | Hotpoint Aquarius WD63 Front Load...

1 Answer

Hotpoint Washing Machine WT741


Error code F12 is indicating a communications error between cards, this can be caused by one of several things..
A problem with bad connections, if you can remove and then replace the plug on connectors, check for loose or chafed wires to motor, they can chafe due to tightness of wires, particularly down to the motor.
It is a electrical problem as opposed to a mechanical one.
If you cannot eliminate the problem your self, then i'm afraid your only other option would be to call an engineer out, it can be a difficult problem to pinpoint correctly.
Please leave a rating for my suggested solution.
Thankyou.

Jan 29, 2009 | Hotpoint Ultima WF860 Front Load Washer

2 Answers

Wt741


not sure if this is repairable but wonderedif anyone else has had the same problem,my wf860 keeps flashing f-03.

Oct 18, 2008 | Hotpoint Ultima WF860 Front Load Washer

4 Answers

Hotpoint ultima wt741


f11 keeps flashing door won't open

Sep 01, 2008 | Hotpoint Ultima WF860 Front Load Washer

3 Answers

Hotpoint ultima wt741


washing machine WT741 ultima all light are flashing and it won't do anything else

Nov 12, 2007 | Washing Machines

Not finding what you are looking for?
Hotpoint Ultima WF860 Front Load Washer Logo

323 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...