Question about Casio Databank DB35H1AV Wrist Watch

4 Answers

No sound I replace the battery and now no tones. Alarm has no sound. When I switch from screen to screen there is no beeping

Posted by on

4 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers
Re: no sound

Take watch spring bar....cut i of....take spring inside the spring bar..use it as a replcement for your lost spring that connect board to bodycase for sound..cut the spring just enough to connect d board and backcase..hope this can help everyone that lost their spring

Posted on Sep 21, 2016

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: no sound

Use a small amount of wire to make contact between the inside of the metal cae and the contact point where the spring was; there are two on the top and at least one in the bottom. Did it myself. I used picture-hanging wire, unrolled a bit and just wide enough for a "patch cord." revisit it when the battery rund down, like 2 to 10 years from now.

Posted on Apr 18, 2015

Re: no sound

When you replaced the battery you must have dropped a tiny spring from the module. This spring activates the beeping sound.

Posted on Oct 14, 2007

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 374 Answers
Re: no sound

Is your battery indicator showing a full charge? Sometimes if it's not showing full then the sounds are disabled. If it's not full tape it to the inside of a window for a couple days and see if that gets the indicator up to "full charge" Otherwise you are going to have to send it in to have it repaired.

Posted on Aug 02, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Timex expedition compass, alarm does not sound since battery replacement.

You will find an arrow head on the outside back of your watch where all the printing is. When you put this lid back on, this arrow needs to be aligned with a notch on the inside edge where the cover goes on. As you are looking at the watch from the back with the cover off this notch is in a northwesterly direction. If you doubt it then just hold the back on without popping it in all the way and hit your mode button to make sure that you hear the beeps again. If you do, then you've found the right spot...

Mar 01, 2015 | Timex Watches

1 Answer

Victorinox Chrono Classic XLS MT Watch

the problem is the battery it has way to much power. usually alarm clock use alkaine battries or energiezer they are best made for things like alarm clocks

Mar 14, 2014 | Victorinox Watches

1 Answer

Citizen QA4360 Sporty watch after battery replacement dont alarm. What is the problem wit it?

If the watch now makes no sound at all, no beeps ever, It seems like the alarm unit noise generator, has been disturbed when you opened it. Ignore the battery and look for the sound transducer behind the holes in the case where the sound comes out. Is it dirty or have any wires to it broken?

Dec 20, 2013 | Watches

3 Answers

Lost the beep on my timex watch alarm

Try taking the back off and orientating it the other way (i.e. turn top for bottom). You don't have to screw it down to see if this will work. As soon as the back clicks in you will be able to hear beeps as you press the buttons

Mar 18, 2010 | Timex Expedition C45981 watch

1 Answer

My watch no longer makes sound. The alarm and tone setting are on. New battery as well. Is it time for a new watch?

Probably you changed the battery in your watch. While doing that the coil spring got lost, so, there is nothing to transmit the sound impulses to the sound membrane. In this case you need professional help from watchmaker. The other cause can be battery on low level. Replace it.
Rate me, plz.

Jan 27, 2010 | Fossil Watches

1 Answer

Replaced battery in lorus digital watch, now the alarm won't work

The alarm spring proabably was lost. If it was, it will not alarm again.

Jul 01, 2009 | Timex Advanced Data Link 53722 Wrist Watch

3 Answers

Timex Expedition alarm beep

good after noon ! maybe the problem of your watch is wrong possition of case back because the speaker or buzzer of your watch is attached on the case back , so open the watch and fix the case back at the correct possition ,!thank you ! god bless !.....

Aug 28, 2008 | Timex Digital Expedition watch

4 Answers

Getting my digital watch to stop beeping every hour

i think the battery is low voltage,try to change the battery 1

Aug 25, 2008 | Timex Sports Ironman Triathlon 50-Lap...

1 Answer

PRG120 button tone

Does the alarm work? if not, it is quite likely the battery is low. You can tape it up in a window to recharge the battery for a couple of days, direct sunlight is not necessary. Normally "Recovering" flashes. If the battery has been depleted for too long, it is possible the battery is now damaged and may need to be replaced.

As for settings, try pressing both buttons on the right side simultaneously in various modes, especially settings or alarm modes and see if that turns back on the beep. Perhaps press the upper left button for 5 seconds until various options start flashing, then try double right button presses and see what happens.

Hope one of these helps.

May 07, 2008 | Casio Triple Sensor Pathfinder PRG60-1AV...

Not finding what you are looking for?
Casio Databank DB35H1AV Wrist Watch Logo

321 people viewed this question

Ask a Question

Usually answered in minutes!

Top Casio Watches Experts


Level 3 Expert

18258 Answers

Arturs Kalnins
Arturs Kalnins

Level 3 Expert

2334 Answers

Jimmy Accardi

Level 2 Expert

97 Answers

Are you a Casio Watch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides