Question about Zebra TLP 2844-Z Thermal Label Printer

1 Answer

Label by label empty

Hi I hve aproblem that the printing is done label by label only means one lable comes empty after one lable prints.

Please help me to solve this problem

Thank you so much in advace..

Regards
Prakash.

Posted by on

  • Stephen Clouthier
    Stephen Clouthier May 11, 2010

    I am guessing you have this hooked to a windows program. more than likely you have an AUTO advance blank page command sending to it after every print job. I do not think it is a paramter you can set on the printer itself so it has to come from the software you are using. You did not mention what that would be.

    You can look at printer settings by pressing the button & HOLDING till it BLINKS 1 time then let go. the settings on the printer, not the software of the program, will print.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

I think that the settings in your label printer driver are not the same as the physical label.
Say you have a 50 x 25mm label , then the settings in the printer driver must be the same, both in the "Properties" and the "Default" Tabs. Also if your printer has a calibration routine, then run this first.

Posted on Feb 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cannot read print on lables


If the labels are empty, replace the batteries. If this does not help, please contact our help desk. The numbers are at dymo.com

Feb 28, 2012 | Dymo LetraTag QX50 Thermal Label Printer

1 Answer

Can't get the Zebra S4m printer to align? How should I trouble shoot this? Sonya


I am assuming you mean misalignment of lable top or start of print moving on label.

check sensor for lable debris.

if OK then perform media calibration:

Enter menu and scroll to ADVANCED

press enter and use password 9999

scroll to MEDIA and RIBBON CALIBRATE

Remove a few labels and remove ribbon

Press right arrow to continue display CALIBRATING PLEASE WAIT.

When complete reload ribbon and labels press right arrow printer will feed approx 39"

printer should now print OK.

Aug 08, 2011 | Zebra S4M Thermal Label Printer

1 Answer

Feeding-problems


you need to calibrate. hold the feed button down intill it flashes 4 times in a row and the quickly let go. it will feed some labels to calibrate and should stop at the tear off. you also have to set label size in the driver to keep from losing calibration.

May 14, 2010 | Zebra TLP 3844-Z Thermal Label Printer

1 Answer

Won't print


Reset the printer to factory defult

May 04, 2010 | Zebra Z4Mplus Label Printer

1 Answer

I have a Zebra Stripe 600. I am trying to print a


Ok, when you say continuous...do you mean it is a roll of label material that does not have gaps in between? If it has gaps...it is NOT a continuous label and you probably have the driver settings set as continuous feed and not gap as it should be....

Call BarcodeWarehouse.biz - they will help you with any problems you have!

Aug 03, 2009 | Zebra Stripe Thermal Label Printer

1 Answer

Whenever I try to print labels, a lot of times it comes out of perimeter.. but sometimes it comes out correctly.. help please!


Set the printer to print labels along with the software your using... This happends because the printer resets after the next page so set the printer too..


Thanks rulds2008


May 15, 2009 | HP PSC 1350v All-In-One InkJet Printer

1 Answer

Printing CD labels , can not get it to line up stright.


I have the exact problem with my HP Deskjet D2360...Done all adjustments, doesn't print in the outline of the label...help

Nov 09, 2008 | HP PSC 1510 All-In-One InkJet Printer

1 Answer

Printing Labels


The MPF is simply the "Manual Paper Feed".
Your printer is set by default that the MPF paper type is "plain paper". Since you are telling the printer that you are trying to print lables, the printer is simply telling you that you need to load the MPF with lables.

If you say "ok", the printer sould continue and print the lables.

If you only print lables, the you can change the default paper for the MPF tray to "lables", and then you will no longer be prompted to load the tray.

Sep 25, 2008 | Dell 5100cn Laser Printer

1 Answer

Printing mixup


Your problem is a computer configuration issue, not a printer problem.

Without knowing any details of your system configuration, it is impossible to offer and further advice.

Steve W
LazerTek, LLC

Jul 02, 2008 | Zebra 140XiIII Plus Thermal Label Printer

1 Answer

Anoterh Vertical Line Problem!


So many questions Vertical lines suggest [you do mean vertical do you - up/and down?] is new one to me try www.fixyourownprinter.com Printing CD's is not a 2200 thing, it is the province of the R series. Printing lables is easy purchase CD labels and suitable CD print software - A kit including labels software and label applicator is available at many computer stores Other labels- download the Avery-Dennison free lable software.

Aug 01, 2007 | Epson Stylus 2200 InkJet Photo Printer

Not finding what you are looking for?
Zebra TLP 2844-Z Thermal Label Printer Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zebra Printers & Copiers Experts

pkwc

Level 2 Expert

254 Answers

lancer284

Level 1 Expert

35 Answers

kenneth njonjo

Level 3 Expert

1575 Answers

Are you a Zebra Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...