Question about Panasonic PV-DM2093 Triple Play 20 in. TV/VCR/DVD Combo

1 Answer

Program timer light blinking

The program timer light is blinking. the remote doesnt work. you also couldnt turn channels. i tried programing my sat. remote but didnt work. i tried inserting blank tape, reset by holding play and fast forward. i got the channels to work only with the buttons on tv. i need to be able to set the time. i think that might fix it, but i cant use the remote

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 398 Answers
Re: program timer light blinking

The timer light blinks when the AC power has been disconnected and the clock is not set. This is how the set warns you that it can no longer do timer recordings. Setting the clock and doing an autoprogram will fix it, but both the remote and the remote receiver must be working. If the original remote is not damaged and has good batteries in it but does not work on that set and you cannot get any other universal remote to work, then the remote receiver (the IR "eye") inside the set has failed and needs to be replaced. I have seen many of those little receivers failing recently. If you do not have experience changing electronic parts on small PC boards then have a qualified tech change it for you.

Posted on Jul 26, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Need code for emerson LD195EMX to program dish remote

This first link provides the procedure on how to program the remote This second link will provide you the codes needed to program the remote to the TV (The top line would be your remote model # you will find this number on the back of your remote, make sure that is the one you enter) If you need further assistance please let me know. Once you have obtained the codes that can address to your television you follow this procedure to program the remote. (Which is the procedure provided on the first link)
Press and hold the clear TV button at the top left hand side of your remote for 5 seconds (all the other clear buttons will light up) once this happens enter the code followed by the # button on your remote, the clear TV button at the top will light up 3 times, this means the remote has been programmed. You can verify the remote has been programmed by trying to up the Volume, once you verify it works be sure to press the SAT button at the top left once (to set remote back to SAT mode and avoid other problems) Feel free to contact me at: if you need further assistance.

Kimberly Escobar
Social Media Representative

Aug 25, 2013 | Emerson EWC1303 13 in. TV/VCR Combo

1 Answer

Remote volume will not work


May 25, 2013 | Emerson EWC27T3 27 in. TV/VCR/DVD Combo

2 Answers

Where can I find a book on the different UVerse Remot tv codes for a new tv?


Universal remote code for Panasonic TV/VCR/DVD combo is


Direct Code Entry
  1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
  3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
  4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.
Code Search If after trying "Direct Code Entry" your device does not respond, or if your brand is not listed, try doing a search of the code library for your code by following these steps.
  1. Manually turn on the device (TV, VCR, etc.) to be controlled.
  2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  3. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks once, then stays on.
  4. Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks, then stays lit.
  5. Press and release MUTE to install the code. The indicator light goes off.
Most users will want to store VCR codes under the VCR button, Cable codes under CBL, etc. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search.

Dec 19, 2010 | Panasonic PV-DM2792 Triple Play 27 in....

1 Answer

What is the comcast cable code for this tv for the digital box


Comcast remote codes for Emerson TV are:-

10154, 10451, 10236, 10463, 10180, 10178, 10171, 11963, 11928, 11913, 11911, 11909, 11905, 11665, 10282, 10280 10270, 10183, 10181, 10179 10177, 10038, 10019
You have to check with each code, until you find which code sets for your TV

programming TVcontrol
The Comcast Digital Adapter remote control is pre-programmed at the factory to operate the Digital Adapter. The Comcast Digital Adapter remote also contains a universal TV library to allow you to control the Power and Volume of your TV.
1. Turn on the TV
NOTE: Please read steps 2 to 4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2.
2. Press and hold SETuntil the Red Light blinks twice, then release SET.
3. Locate the code for your device in Manufacturer's Codes on the back of this user guide. Brands are listed in alphabetical order with the most popular codes listed first.
4. Enter the first five-digit code for your TV. If you perform this procedure correctly, the Red Light will blink twice
NOTE: If you enter an invalid code, the red light will display one long blink and exit the programming mode. Repeat steps 2 to 5 with a valid code.
5. Aim the remote control at your TV and press Power once. The device should turn off. If it does not respond, repeat steps 2 to 4, trying each code listed for your brand until you find one that works. If it still does not work, try Searching For Your Code.

Searching For Your Code
If your brand of TV does not respond to the remote control after trying all of the codes listed, or if your brand is not listed at all, try searching for your code.
1. Turn on your TV.
2. Press and hold SETuntil the Red Light blinks twice, then release SET.
3. Enter in 9 - 9 - 1. The Red Light will blink twice.
4. While pointing the remote control at the TV and press and release the CH + key until the TV turns off. (Note: You may need to press [CH+] numerous times).
NOTE: In the search mode, the remote control will send IR codes from its library to the TV.
5. Press SETonce to lock in the code. The Red Light will blink twice.

Dec 03, 2010 | Emerson EWC1303 13 in. TV/VCR Combo

1 Answer

Trying to get my directv remote to control this TV but none of the Sylvania codes recommended work any ideas

slide the mode switch to tv, hold down mute and select until the light blinks enter "9-9-1-------1" when the lights finish blinking start pushing push the channel up button. this is a code search. It will transmit every code it knows one at a time. when the tv turns off you've found a code that works. turn it back on, try the volume and see if it works correctly. when finished press select.
most tv/dvd and/or vcr combos won't work with tv codes.
Directv has posted many new codes on their website for combo tv's Go to [ ]to look up the latest codes read the programming section for the remote as there are many customizable features on the remote that most people aren't aware of. good luck

Sep 23, 2009 | Sylvania 6719DC 19 in. TV/VCR/DVD Combo

1 Answer

Zenith TVBR1352Z TV/VCR combo. I cannot get a code to allow my Philips/Direct TV remote to control the TV/VCR. All I really need it to do is control the volume

Turn on your TV (or other device). You will have to do this manually until you program your Philips remote control

Look for the "Setup" or "Code Search" button on the Philips remote control. Which button your remote has will depend on the exact Philips remote control you are using. This button may be a different color or may be labeled.

Hold either the "Setup" or "Code Search" button for about 10 seconds. If your remote has a light, the light should begin blinking. If there is no light, you can just count to 10 and then let go of the button.

Press the "TV" button on the remote to program the Philips remote to your television set

Find and press either the "Up" or "Down" channel button on the remote. Continue pressing either button until the television channel changes. This may take several minutes. Once the channel changes, press the "Power" button on the remote to turn off the TV. Your Philips remote will now be programmed to your television.

Jul 09, 2009 | Zenith TVBR2562Z 25 in. TV/VCR Combo

2 Answers

Sylvania 6313CB 13" TV/VCR replacemnt remote

We have a Sylvania 6313CB TV/VCR combo.  I bought a universal remote and the code would not work when I tried to program it to the "TV" button using all those possible codes listed in the books.  So, on the universal remote, there was a button named "VCR" and when I programmed in the code "0000" all worked.  This was a $6.00 universal remote named "One For All"  we bought at the Big Lots store.  
Specifically, here is what I did:
Turned TV on Pushed the "VCR" button and light blinked once Pushed and held the "set" button until it blinked twice Released the "set" button and entered the numbers "0000" Pushed the on/off button and it worked including volume, channel up/down and channel change by entering the channel number.
Hope this works for you too.

Jan 14, 2008 | Sylvania 6313CB 13 in. TV/VCR Combo

1 Answer

Tv Combo will not work with replacement remote

my panasonic tv model no. PV-DF2704, program light is blinking and I don't know how to cut it off. It is causing my tv to cut off. My remote control will not work. I bought it second hand. I program a universal remote and it works for a little while, but I can not set my tv for cable. Please help me if you can.

deborah from Louisville

Nov 12, 2007 | Panasonic PV-DF2704 27 in. TV/VCR/DVD...

2 Answers

AIWA VX-T1420 Setting Channels

No it should not light up. If you can not go into menu and add channels manually or auto program. Then you will have to get a remote to work. You could order original

Sep 23, 2007 | GE 13TVR60 Combo

1 Answer

My TV Says Line and Displays Just One Channel

Unfortanatly, your gonna need the original remote or a simular one to get to the channel programming mode in the menu. You can go to or call 1-800-remotes and get one for your set. Im sorry i couldnt assist you more. Good Luck

Jul 12, 2006 | Panasonic PV-M2048 20 in. Combo

Not finding what you are looking for?
Panasonic PV-DM2093 Triple Play 20 in. TV/VCR/DVD Combo Logo

733 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Combination Televisions Experts

The Knight
The Knight

Level 3 Expert

66444 Answers

Cindy Wells

Level 3 Expert

4720 Answers


Level 3 Expert

6993 Answers

Are you a Panasonic Combination Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides