Question about Sanyo PLV-Z4 Multimedia Projectors

1 Answer

Replacement lamp I recently acquired a Mitsubishi 62" HDTV which the lamp has gone out on. I purchased a new lamp and installed it however there still is no picture. The TV will power on for a short time with no picture and then it will power off and the lamp light will come back on. In the manual it says to reset it by selecting menu on the remote however with no picture that is not possible to do. I did use the system reset on the front of the TV and it still didn't work. What do you suggest?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 167 Answers
Re: replacement lamp

Have the tv looked at by a professional that knows what he's doing.

Posted on Jan 26, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Just replaced the lamp in an XD520U and am having the same problem, but not hearing any high pitch noise. The Lamp has been reset correctly, and checking the info screen verifies it, but still after a

Have you used a genuine replacement lamp? There are some clones coming from oriental sources that do not accurately match the specifications of the original, and it's possible this may be the cause of the problem...
Was the old lamp still working when replaced? If so, reinstall it teporarily and see if the problem has gone. If so, it's the new lamp that's the cause of it

Mar 26, 2014 | Mitsubishi XD520U DLP Proj XGA 2000:1 3000...

1 Answer

I have two steady red lights on my projector. I just purchases a replacement bulb that is the bulb only. Is there any tricks to the installation and will this resolve the problem?

What is needed is to remove the lamp door and remove carefully the lamp assembly. Now clean the filters, make sure that there is no dirt accumulation. Use gloves when you are handling and replace the new bulb carefully into the holder slot., make sure that this is tight before you screw the holding brackets.
repace the lamp door and switch on, now reset the lamp hours by using the menu > settings> reset .
Please find tips from a link below;

Oct 07, 2011 | Mitsubishi HC900 Multimedia Projector

1 Answer

The projector will turn on normally, but after about 20 seconds the screen will go black and the "temp" and "lamp" alarm lights will flash on and off. I've changed the filter and we...

if you are replacing the lamp by yourself, and if you are touching the lamp body with your fingers, the lamp will be damadged fastly; because the lamp is sensible. the temperature of the lamp increase abnormally so the message 'temp' and 'lamp' increase. to solve the problem you need to replace a new lamp, but you have to install it at the BenQ service it's free.

Jan 02, 2011 | BenQ W10000 Projector

1 Answer

Replacement bulbs burn out within a month

If you did not purchase the OEM Sony manufactured bulb (model LMP-H200) then you likely acquired a poor quality "after market" lamp. I recently purchased a replacement lamp for my VW60. The list price is $369, I paid $269 from a reputable brick and mortal / on-line retailer.

If you paid substantially less than $269 or bought from an unknown on-line seller, your lamp is likely the problem. Note I have seen some shady on-line sellers (with "electric" in their name) sell knock of bulbs for the same price as the OEM.

Hope this helps.

Jan 19, 2010 | Sony BRAVIA SXRD VPL-VW60 LCD Projector

1 Answer

Projector attempts to light the lamp, but to no avail

the ballast is gone and needs replacing. unfortunately, infocus has no parts for that model.

Oct 30, 2009 | InFocus Multimedia Projectors

1 Answer

Need to reset lamp timer

The lamp timer expiring would not shutdown the unit typically. Purchase a replacement lamp and included will be the instructions to both replace the lamp and reset the timer.


Apr 15, 2009 | Mitsubishi ES100U Multimedia Projector

1 Answer

Alternating power and lamp status lights

...replace the lamp. The lamp is most likely WAYYYYY past its prime so I suggest starting there. Sometimes even if you had just replaced the lamp the new lamp could've blown. When there is no signal running through the lamp circuit there is no signal to the display sensor, which means no image.

hope this helps!

Jan 28, 2009 | Mitsubishi XD300U Multimedia Projector

2 Answers

The Protectiopn circut is working

Hi there

Did you check that your lamp hours were actually reset ?

Mar 27, 2008 | Mitsubishi XL1XU Multimedia Projector

Not finding what you are looking for?
Sanyo PLV-Z4 Multimedia Projectors Logo

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sanyo Multimedia Projectors Experts


Level 3 Expert

2236 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

66352 Answers

Are you a Sanyo Multimedia Projector Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides