Question about Compaq ProLiant ML370 G3 (340262-001)

1 Answer

What do the front panel leds on the ml370 g3 represent?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 28 Answers

External health (power supply) LED

Green Normal (system on)
Amber Redundant power supply failed
Red Critical power supply failure
Off Off = Normal (system off)

~gnomer

Posted on Feb 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kingston Datatraveler G3 8GB VID=04F2 PID=B026 Can't Format, 0 byte yongkowidjaya@ymail.com


click start click on my computer you should see your usb drive
right click then select format
another way is to control panel administrative tools computer management disk management right click on your drive select format

Oct 24, 2013 | Kingston Computer Cases

1 Answer

Acer 915m08 front panel conectors


http://forum.novatech.co.uk/showthread.php?45-Generic-front-Panel-Wiring-Guide-Updated
here's a recent link fix for your information.

Jun 08, 2012 | Acer Veriton 7700g Power Button & Led...

1 Answer

Chieftec Dragon


Go to Asus main site...Also you could check remaining cables some of them must be for that activity you searching for...

Apr 17, 2012 | Chieftec Dragon DG-01BD-U black

1 Answer

I have a new pc case on the front panel connectors their is one hdd led +- and one hdd led plug were do they go my case is a EVO LABS E-6690 BLACK/RED, 12CM LED FAN, INC DOOR AND SIDE WINDOW my mother...


You need to look in the handbook that cam with your motherboard for a section labeled 'Connectors' or possibly 'Connections'. There will be one USB 2.0 type prong on the motherboard that is designated for case connections [Power LED, mini-speaker, etc.]. The manual for the motherboard will indicate what order and where on the motherboard your connectors should go.
Good luck with your build. :]

Aug 26, 2011 | Computer Cases

1 Answer

How do I open the front plate of the Orion 201 tower to replace the 90mm LED case fan?


There are plastic tabs on the inside of the case (near the front) that need to be "popped out" in order to remove the front panel.

Feb 21, 2011 | Azza Orion 201 black/silver SECC Steel ATX...

1 Answer

Fan is not moving, front panel led is red


If your computer will nor start and the system fans do not turn on and stay on when you power on your PC, then either the power supply has failed, a component connected to your motherboard has failed or the motherboard itself is defective .
Power supplies require a "power good" signal back from the motherboard before they will operate.. In order to test a power supply, you need a PC power supply tester. Without one, you will either have to take you power supply to a PC technician and have him test it or install a known good power supply in your computer.
If you have any additional questions contact me by clicking on the "Add a comment" link located under your problem description on FixYa. Also, if you believe that this information was helpful to you, please rate my solution using FixYa's "Solution Helpful" rating scale.
Best regards,
Yavacotech

Feb 18, 2011 | Compaq ProLiant ML370 G3 (340262-001)

1 Answer

Case wiring


For the wires that comes in your CPU casing, mostly used for your front panels like power switch, hdd status, power led, etc. It is indicated on the pins itself so you might not be confused. there are some that comes for front panel USB. (with codes like vcc+ /- ,etc.). The best you can do is to read your Mainboard manual on where you place this pins.

Feb 25, 2009 | Avus A450-3001 Micro ATX Mid-Tower Case

1 Answer

CDROM isn't recognized. Has interrupt conflict with hard drive


once you login to the safe mode and try to resolve it .. i am sure your problem will be resolved in the safe mode ...

because safe mode loads will the minimal set of drivers it is usually used to resolve the hardware conflicts, graphics related problems ..

you can go to the safe mode by pressing the F8 key at the system boot then you must select safe mode and press enter on it .. after that you will be in safe mode after some seconds .. then you can try to resolve the conflict ..

any further problem you can leave me a new comment ...

regards
-Dileep

Dec 03, 2008 | Compaq ProLiant ML370 G3 (340262-001)

1 Answer

Hardisk have difrent amount


Because Compaq has a hidden partition on you're C:\
Stored in that hidden partition is Compaq's restore drivers & software. If & when you need to run the restore CD on the Compaq, the restore CD enter's that partition & uses the software to help in the process of restoring the C:\ drive to factory settings. (This is normal for most Compaqs).

Mike

May 07, 2008 | Compaq ProLiant ML370 G3 (340262-001)

Not finding what you are looking for?
Compaq ProLiant ML370 G3 (340262-001) Logo

Related Topics:

2,749 people viewed this question

Ask a Question

Usually answered in minutes!

Top Compaq Computer Cases Experts

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Josh Whitehead
Josh Whitehead

Level 3 Expert

1146 Answers

Are you a Compaq Computer Case Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...