Question about Dynex 19 in. LCD Flat-Panel HDTV

Open Question

My 19 inch LCD Dynex tv has frozen on certain channels

I'm having a little bit of trouble with my tv. It is frozen on certain channels (9 of about 80). This has been happening for awhile. When I flip to the certain channels, there is a still shot. There is also no sound. I can move onto other channels just fine. The channels that were frozen has changed about three times, each time the amount of channels stuck is getting larger.

Well, no instead of just showing a still shot of the channel, the screen for these channels has become black. There's still no sound.

Posted by on

6 Suggested Answers

bhiga
  • 119 Answers

SOURCE: Only channels 2-13 show on new Dynex 19" LCD TV

You'll need to find the Cable/Antenna setup and change it from Antenna to Cable. Sometimes the setting you want is called CATV.

Posted on Aug 13, 2008

usmcdcf
  • 5 Answers

SOURCE: 19'' Dynex TV does not come up as a Computer Monitor.

I had this same problem with the 19" model as well. I had to reinstall video driver with the tv hooked up in order for the resolutions to work properly. In order to do this I used an S-video cable which worked well enough to reinstall the video driver. I did not try safe mode which might have been easier, I just did not think of it at the time. With the video driver reinstalled while the TV is attached to my computer, I know enjoy a crisp 1440x900 screen resolution. Hope this helps.

Posted on Jan 06, 2009

jamielwright
  • 75 Answers

SOURCE: Dynex 19Inch Vga no signal

You may need to set up the video card to see the TV so you can display the computer on it.Somewhere in the setting for your video card should be settings for that.

Posted on Jun 01, 2009

tvservice306
  • 458 Answers

SOURCE: I have a Dynex DX-LCD37 tv and the channel memory does not hold.

try use out door ant

Posted on Aug 14, 2009

  • 2 Answers

SOURCE: Dynex 32" 720 LCD HDTV - no channel listing after run auto scan?

Excuse me but the other answers are written by people who have not actually confronted the problem and are just guessing. They are all wrong. Here's the answer:

If your TV is expecting a TV input, it will keep searching for at least one TV channel on cable or antenna. If you only have a DVD player plugged in, for example, or if your cable is hooked up wrong, so there's no video signal on it, the TV will keep searching forever. (This is an unforgivable design flaw, by the way. But then, it was a cheap TV, wasn't it?)

To solve the problem, look at your remote control. You will find input buttons. Mine are small, along the top, right under the "power" button. Try pressing "video" for example, instead of TV. That stops the TV from hunting for TV channels.

Have a merry Christmas. Enjoy your new TV. Watch it in moderation and eat fruit and vegetables every day.

Posted on Dec 25, 2009

  • 3 Answers

SOURCE: need code for Dynex/DX-l42-10A for Dish Network

I know you've probably figured this out by now, since you posted last May, but I figured I would post the solution, since I just found it, and someone else may want to know.
I bought one of these sets the day after Christmas 2009, and finally figured out the code that works with the Dish Network 5.4 IR remote.
I did a Code Scan, and found that the code that works is 721. In the Dish Network listing, this is listed as the third code for Sansui.

Hope someone finds this useful, even if it's too late for you.


Posted on Feb 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dynex 19 inch lcd tv does not show picture standing up but will show it laying down


check the ribbon cable that connects the screen to the mainboard may have a loose connection

Feb 02, 2013 | Dynex DX-LCD19-09 19 in. LCD TV

1 Answer

Certain channels do not have sound but the picture is clear


Most of the time its not your TV its the TV stations signal. Unless you live like in a nursing home were there are a gang of cable boxes and there is an adjustment on the box it self. We have them in our faucilty.

Sep 09, 2012 | Dynex DX-LCD19-09 19 in. LCD TV

1 Answer

I need a code for dish network i just bought a tv dynex 19 inch tv lcd


Hello, I hope that this has been resolved for you already, but if not, pleases follow the link below, and that remote will be working with the tv in no time!!!!!

http://www.dishnetwork.com/SupportSection/power-scan-instructions


Becki Barned
DISH Network Customer Service

Nov 22, 2010 | Dynex 19 in. LCD Flat-Panel HDTV

1 Answer

Need tv code for Dynex 19" for Radio shack 8-in-one remote


i have a 42 inch dynex tv and i have a LUMINOUS JUMBO REMOTE on the top of the remote it says 8 FUNCTION REMOTE and i cant find a code that works for the tv can someone help me plezz

Sep 23, 2010 | Dynex 19 in. LCD Flat-Panel HDTV

1 Answer

2 year old LG Flat screen TV keeps freezing


It is not your tv its channal 9, switch off totally at the wall, disconnect aerial, turn on - tune into channel other than 9, plug in antenna again

Feb 04, 2010 | Goodmans GTVL19W17HDF 19 in. LCD TV

1 Answer

I have a dynex 19 inch tv that wont turn on can you help


Look at the power supply first; look for burnt parts, bad capacitors, etc. Look for 5vdc, 12vdc, and 24dvc.
http://en.wikipedia.org/wiki/Capacitor_plague
Parts: http://www.shopjimmy.com/catalogsearch/result/?q=Dynex+DX-LCD19-09+
Please post back what you find

Dec 18, 2009 | Dynex DX-LCD19-09 19 in. LCD TV

2 Answers

How do i cahange my reception From analog to digital?


The Dynex LCD-19-09 19in LCD Tv has a digitial tuner in it already. I would recommend doing a channel scan and make sure it is on the "Antenna" setting instead of "Cable" and let it scan for channels. You will see all the analog channels like "7", "12" if they are still broadcasting, however, if you can pick up the digital channels, it will look more like "7-1" or 12-1; 12-2 etc.". To get to this, push the "Menu" button on the Dynex remote, then arrow down twice to TV, then push the right arrow and make sure it is set at Antenna and do a channel scan. Should get you whatever digital channels are available. If the digital antenna is not strong enough, you will need to get the digital one at Wal-Mart as previously suggested and hope that will convert the analog channels in your area.

Jun 12, 2009 | Dynex DX-LCD19-09 19 in. LCD TV

4 Answers

Dynex (no database) since power outage


What you have to do it go to the TV Menu and go to channel. Then go to channel scan and do one of those. THe problem is that is just doesnt know where to look for channels, but a quick scan will fix that.

Oct 03, 2008 | Dynex 19 in. LCD Flat-Panel HDTV

1 Answer

Dynex 19" tv


Go into the setup screen on the TV and set the channel option to CABLE (it is probably set to AIR right now or something).

The website should also have a manual for how to program the remote.

Sep 08, 2008 | Dynex 19 in. LCD Flat-Panel HDTV

1 Answer

Only channels 2-13 show on new Dynex 19" LCD TV


You'll need to find the Cable/Antenna setup and change it from Antenna to Cable. Sometimes the setting you want is called CATV.

Aug 12, 2008 | Dynex 19 in. LCD Flat-Panel HDTV

Not finding what you are looking for?
Dynex 19 in. LCD Flat-Panel HDTV Logo

Related Topics:

340 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dynex Flat Panel Televisions Experts

The Knight
The Knight

Level 3 Expert

68368 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

Cindy Wells

Level 3 Expert

4761 Answers

Are you a Dynex Flat Panel Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...