Question about Sharp AR-M350U Copier

1 Answer

Error Code F1-87 Finisher Trouble on Sharp AR-M350U+

Received this error code when my machine was turned on this morning.

Error Code F1-87 Finisher Trouble on Sharp AR-M350U+.

I turned the machine off and back on and error was not their anymore. Still wondering what that code means.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 126 Answers

It is a stapler rotation error. The stapling tray pressure arms become dull at the tips, so when the stapler attempts to move into position to make the staple it cannot move the guides out of the way.

First choice) Replace the (4) stapling tray pressure arms (LSTPP0357FCZZ). After you replace them you'll see that the tips get worn down, and wedge into place so that the black support plates cannot move out of the way of the stapler. The black plates look warped, but they aren't (I should say they always look like that).

They are fairly easy to get to. You do have to remove the finisher from the copier. Remove the front and rear covers. Open the right door. Pull the pins that retain the door. From there you'll see the arms. They can be changed with a little maneuvering.

2nd Choice) Clip overtight wire ties to the stapler rotation home position sensor.

3rd Choice) Shake down the stapler to its bottommost position (wherever it settles is fine). Adjust the flag that triggers the stapler home position sensor. If I remember correctly its the narrow **** in the flag.

Posted on Jan 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error code F1-15


You have a problem with tray movement in the finisher/sorter area. Sometimes those trays get slightly bnt if somebody leans on them and they dont strike the sensor in the center properly. If not then maybe the upper and lower limit sensors need to be cleaned or replaced

Jul 24, 2012 | Sharp AR-M350U Copier

1 Answer

Error code h4-00


fuser temp trouble, try reseting the machine with SIM 14 if problem returns, try SIM 5-2 to check fuser lamp.

Aug 13, 2010 | Sharp AR-M350U Copier

1 Answer

Sharp AR-M350U Copier/Printer Error Code F2-00


clean developer unit connector .pull out , clean , then insert .

May 25, 2010 | Sharp AR-M350U Copier

1 Answer

Error Code


A error code F1-09 deals with the finisher of the copier. Have the bins gotten stuck or got something in it's way when moving up & down. I would turn the copier off and unplug the finisher from the copier, 1 screw holds connector in. Then I would turn it back ON and see if the code is gone, if so reconnect the finisher and you should be good to go...

Jun 11, 2009 | Sharp AR 201 Copier

1 Answer

Error code h5-01


Hello sir; the paper exit sensor get stock, just put back in the track let it moved free.

Apr 14, 2009 | Sharp AR-M350U Copier

1 Answer

Sharp AR-5127, the error code U2-40


U2-40 is a board error, F1-15 is finisher lift motor error.

To reset: #, interrupt, clear, interrupt. (screen should say service mode), enter 16, print, are you sure? , yes.

For the finisher error, follow above procudure, entering 14 instead of 16. if error returns, disconnect the finisher

Nov 26, 2008 | Printers & Copiers

Not finding what you are looking for?
Sharp AR-M350U Copier Logo

2,046 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Printers & Copiers Experts

George Mclaughlin

Level 2 Expert

330 Answers

Soulvisitor
Soulvisitor

Level 3 Expert

1113 Answers

Vito Suglio

Level 1 Expert

23 Answers

Are you a Sharp Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...