Question about Maytag Neptune Washer

1 Answer

Neptune MAH3000AWW will start to fill when start is pressed, but stops seconds later

When we setup the washing cycle than press start, the washer starts to fill with water, but a couple seconds later, it shuts down completely. If we push it again a minute later, it starts again, but just as quickly, stops filling a few seconds later. Please offer any suggestions you can, we are retired and can't afford to get this thing fixed. Thanks

Posted by on

  • Anonymous Mar 14, 2014

    washer will wash complete cycle then loose power a few minutes later. you can unplug and reset the washer and wash another complete cycle if you don t wash the washer will still loose power just sitting there no in any cycle

  • Anonymous Mar 26, 2014

    I did replace the wax motor already.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 51 Answers

Either a faulty pressure switch / pot or faulty controller - either way you will need to call someone in.

Posted on Jul 25, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Maytag washer wiring diagram


machine start when you push the start button but stops 3 or 4 seconds after the button is released help me dennis montgomery maytag neptune model #mah3000aww

Aug 27, 2010 | Maytag MAH8700AWM Neptune Front Load...

1 Answer

Tub filled with water, Lr code


To pump out the excess tub water while failing to complete spin cycle;

Enter Service Mode by simultaneously pressing and holding the Enviro Plus and Spin Only keys for three seconds or the display reads “00”

Pressing the Delicates key will lock the lid. Now press the Presoak key the drain pump will turn on. Stop with off button or hit the Presoak key.


This process is documented in the Service Manual. I would go to page 16 of the SM lower right hand part of page, Board Output Test and turn on the drain pump in service mode to pump out the tub.



If I could ask you to do a little troubleshooting;

It sounds like the wash/agitate cycle completes and you enter into the spin cycle of the selected wash cycle is that correct. When the wash cycle fails does the Cycle Status LED indicate that the washer is in the Spin cycle?

With a empty wash basket no wash load in the basket and you start a Spin Only cycle will the Spin Only cycle complete?

If the washer will start the cycle do you hear and loud Spin Only cycle noise such as metal against metal grinding noise?

With the washer off and no clothes in the wash basket can you open the lid then Spin the wash basket as fast as you can in the CCW direction the only direction. The wash basket should spin CCW several rotations and coast down to a smooth stop dose it?

I’m checking for Outer Tub increased bearing resistance…..Rich


FAV6800A/FAV9800A Service Manual for reference. Sears Parts Direct for reference.

Jun 28, 2010 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Maytag Neptune TL starts, fills with water a few sec then clicks loudly a few times and then stops, a few sec later it repeats this, then stops for good. Tried unplugging and restarting, but same thing...


Any error codes?
Do you want to troubleshoot? If so here is the Service Manual.
FAV6800A/FAV9800A Service Manual for reference. Sears Parts Direct for reference.

I would start by removing the front cover of the machine follow all safety warnings in the Service Manual.

Follow the first few steps in my Clutch Fix post to remove the front cover.

Then let me know if during the water fill cycle the machine rotates the wash basket CCW in a slow spin during the water fill cycle before the machine stops and we will go from there. Give me all the detail you see with the front cover off I need to know if the wash basket is rotating CCW during the washer fill cycle.

You can lift the washer top up a slight amount to observe the slow CCW spin of the wash basket. I’m checking that the outer tub bearings are not seized……Rich
To pump out the excess tub water with this process;

Enter Service Mode by simultaneously pressing and holding the Enviro Plus and Spin Only keys for three seconds or the display reads “00”



Pressing the Delicates key will lock the lid. Now press the Presoak key the drain pump will turn on. Stop with off button or hit the Presoak key.



This process is documented in the Service Manual. I would go to page 16 of the SM lower right hand part of page, Board Output Test and turn on the drain pump in service mode to pump out the tub.

Jun 26, 2010 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

GE PROFILE WASHER DOESN'T CYCLE TO WASH FROM FILL


  1. Clear the ERROR from the screen: Press and hold the MY CYCLES and BACK buttons simultaneously for 3 seconds. The control will display any recorded errors. Please write down what error codes are shown on your screen in case service is needed. If a MORE icon is displayed on the screen, press MORE to list additional errors. When the EXIT button appears, press EXIT.


  2. Remove Power: Follow the onscreen instructions to remove power (unplug unit) and then immediately plug unit back in.


  3. Clear Setup Mode: After power is restored, a setup screen that begins with "Congratulations..." will be shown. DO NOT PRESS the OK button shown at the bottom of the screen. Press the START/STOP and POWER buttons simultaneously until the Home Screen is displayed. Your unit is ready to function normally.

Aug 19, 2009 | GE Profile WPRE6100G Top Load Washer

1 Answer

Maytag neptune washer stops after filling with water on the first cycle...will not spin Neptune stops after filling. No codes. Lid unlocks. Ideas?


Hello n8mtsn,

I would pull the 120VAC power cord to the washer for 10 seconds then power back up.
See if you can get into service mode. To enter Service Mode press and hold he Enviro Plus and Spin Only keys for three seconds or until the control beeps and the display reads “00”. If you can’t get into Service Mode I feel you have a Control Board issue/failure.

If you can get into Service Mode then go to page 15 of the SM and we want to try a Quick Service Cycle test. Follow the instructions to enter the Quick Service Cycle test and let us know the results. If the test will run it will take about 10 minutes.
Link to Service Manual for reference. Sears Parts Direct for reference.
Rich

May 30, 2009 | Maytag Neptune FAV6800AW Top Load Washer

2 Answers

MAH3000AWW Trips 20Amp Breaker at rinse cycle


The motor is known to have bad windings. Do a search for "Neptune Washer will not start" Also just inside the control panel where the start/stop sw is should be a paper folded with the diagnostics test and schematic. It is tucked under the pressure sw attached to the back. If not there then search "Maytag Neptune motor phase test" There is also a Service Manual FREE at Goetlieh's site.

Sep 27, 2008 | Maytag Neptune Washer

1 Answer

Maytag Neptune rinse cycle doesn't start.


cold water valve screen plugged or bad valve, just check it!

Aug 06, 2008 | Maytag Neptune MAH6500A Front Load Washer

2 Answers

Neptune MAH3000 Stops


did you just replace the fried part or did you get the board kit guest you may have a bad tacogenerator in the motor check the resistance of the motor

Dec 12, 2007 | Maytag Neptune MAH5500B Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

402 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

588 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

John Tripp
John Tripp

Level 3 Expert

4655 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...