Question about Bosch WET 2820 Front Load Washer / Dryer

Open Question

Clicking but not starting cycle,

All lights working but doesn't start. This problem has occurred after scottish water cut off water mid cycle, had to drain the load of washing in the machine at the time but not working since.Is there a way to reset the machine? or suggests on how to fix it?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: 2nd Bosch washing machine same problem

put tester on drain pump power wires and see if power is there. if so,your pump or the line is blocked.  

Posted on Oct 11, 2007

  • 1 Answer

SOURCE: WFD 2460 will not start wash cycle after it has filled with water

Isolate power and water supply and gain access to the main drum motor. Check for condition of carbon brushes by removing them and repla
ce if severely worn. Check wiring loom around motor and right back to module controller. The clicking is obviously power being supplied to motor via the loom to the motor. finally check for any dry solder joints or burnt areas on the circuit board controlling the motor.

Posted on Dec 07, 2008

barkencoa
  • 3463 Answers

SOURCE: Bosch WFF1201 Washing Machine, wont drain

To access the pump filter, remove lower plastic panel at front of washer, there you will see the filter, unscrew filter cover anti clockwise, remove and clean filter.
You will probably find that whatever was causing the clicking noise is something in the filter.
If you can't see anything in it , then have a look inside the pump housing before you replace filter.
Plz rate my solution .
Thanks.

Posted on Jan 26, 2009

  • 228 Answers

SOURCE: bosch maxx 1100 WLF 2260uk.it takes water in but

no drum rotation motor brushes failed cheap and easy to replace.

Posted on Dec 15, 2009

  • 1 Answer

SOURCE: bosch WET 2820 dryer pumps in water

The problem was the thermostat in the drying inlet chamber. Very easy to get to and very easy to change.

Part No.175369 (NTC sensor)

Regards

PJPJ

Posted on Jan 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Water starts to pass through but then stops and error alarms start


see this causes and fix it. God bless you
Lid Switch Assembly If the washer stops mid cycle the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design.

Door Lock Motor and Switch Assembly If the washer stops mid cycle the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design.
Water Inlet Valve If the washer stops mid cycle the water inlet valve cold water side may have failed. Most washers have a cold water rinse and so if they can't fill with cold water they just sit indefinitely waiting for the cold water to enter. If there is cold water to the water inlet valve and the cold water works in other parts of the cycle - or to make warm water - the valve is not the problem.

Main Control Board If the washer stops mid-cycle the main control board might be defective. This is not common. Check other causes first such as the lid or door switch and other components.

Timer If the washer stops mid cycle the timer might be defective. This part is often misdiagnosed, check other components before replacing this timer.
10_5_2012_6_57_01_pm.jpg

Oct 05, 2012 | LG Washing Machines

1 Answer

Frigidaire FDB126RBS2


Be very careful, it sounds like an electrical failure, were the machine has cut out to protect you and itself. You need an expert there and quickly. Water and electric are a bad mix and more house fires are caused by washers than most other appliances.

Sep 23, 2012 | Dishwashers

1 Answer

Favorit 44070 3 flashes on end of cycle light. No water loading. Does not start


you need a water valve if the overfill float is not malfunctioning

Aug 27, 2012 | Bosch Dishwashers

1 Answer

Maytag MDB4651AWS Dishwasher will not start.


Do you ever hear the fill solenoid click on to begin the filling. That is the first thing that has to occur. The water supply generally connects right to that solenoid. Ohm out the solenoid coil. ( breaker power off)

May 21, 2012 | Maytag Dishwashers

1 Answer

Set dial and water overflows, doesn't stop sending water in tub, No spin cycle


The water level sensor is faulty and so it does not switch even with water level coming to the set level. Unless the water level switch is triggered the water inflow will not stop because the inlet valve will not cut off.Remove the water level sensor and check if the diaphragm is working , if not it must be replaced.

Mar 13, 2012 | Washing Machines

1 Answer

Starts water cycle then stops


Probably needs new carbon brushes in motor.

Dec 17, 2011 | Bosch Washing Machines

1 Answer

Hello all, Whilst using my XP510i for the first time today, the amp has simply died. Didn't have the music on loud, was only in the green lights section of the amps display, but whilst trying to make...


The amps on the unit have probably died. Did they replace it for you? I'm becoming alarmed at the number of units just dying for an $800 piece of equipment.

Jul 31, 2011 | Audio Players & Recorders

1 Answer

I have a Maytag Model A412, series 11 washing machine. After the machine fills with water the machine appears to start its cleaning cycle but the agitator doesn't work. The water starts & the...


if this is a two piece agitator,it should behave like a ratchet turn freely clockwise and catch counter clockwise if it doesn't catch the agitator "dogs " are shot this is a verry inexpencive repair

Jun 08, 2011 | Washing Machines

Not finding what you are looking for?

Open Questions:

See all Bosch WET 2820 Front Load Washer / Dryer Questions

Bosch WET 2820 Front Load Washer / Dryer Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Washing Machines Experts

Tim Whalen

Level 3 Expert

3074 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...