Question about Hotpoint Ultima WF860 Front Load Washer

1 Answer

Hotpoint wt940 "Door " displayed sops midway through cycle

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

The door is not locking , possibly caused by the interlock itself or motor brushes worn ( most likely if machine is a few years old at least ) could also be no power to lock via control board .

Posted on Jan 23, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hotpoint 7 cycle agitator sopped spininng/10 years of flawless operation


Possible there is no power to the motor at the cycle of spinning or agitation. It is possible that the program controller unit is a suspect, you need to use a multimeter to confirm the case as the power to the motor could be measured

Aug 17, 2012 | Whirlpool Washing Machines

1 Answer

Hotpoint Ultima wt940 I load washing and set a normal program (say 40 degree wash). The door is firmly closed. I push start. Even though the LCD is on and I have pushed start - there is no...


Hi from retired Englishman in SW France,
'door' stands for Door Error. There is likely to be a problem with either the door solenoid/lock or the 'door closed' sensor requiring a service engineer's attention I suggest ;-0(
If this has assisted and/or clarified the situation for you please consider a 4 thumbs up on our rating.
Thanks and good luck!
John C

Jun 18, 2011 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

I have a hotpoint ultima wt940 washing machine,, which is displaying a tap symbol,, when it fills up at the start of the cycle,, h2o flashes on the screen,, then the machine stops. Any advice? Thanks.


H20 is indicating a problem with the water supply.
Check tap/s are turned on fully, no restriction in hose/s, and make sure that there is sufficient water pressure.
Another possibility is that the inlet valve/s are faulty inside the washer.
Please rate my solution.
Thanks.

Nov 07, 2009 | Washing Machines

1 Answer

Error F01


i have the same problem the machine gets part way through a cycle and then stops and Displays F1.

Oct 03, 2009 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

It's Leaking Water!


Most common reason is that the lower spray arm splits on the seem and sprays water under the door, to proove if it is this remove lower spray arm and run through program if no leak fit new arm. Regards Advisor

Aug 30, 2007 | Hotpoint 24 in. FDW60 Free-standing...

Not finding what you are looking for?
Hotpoint Ultima WF860 Front Load Washer Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

puggy666

Level 1 Expert

48 Answers

ptpumpman

Level 3 Expert

407 Answers

Cindy Wells

Level 3 Expert

5160 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...