Question about Cobra 19 Ultra II CB Radio

1 Answer

Which pod controls wattage output on Cobra Ultra 19 3

The board is stamped 19DX-IV

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Cobra Master
  • 1,795 Answers

L-21,L-22,and L-17 on a scope for 4 watts max output.

Posted on Dec 17, 2014

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 40 Answers

SOURCE: PEEK IT

not a good idea to do it yourself you need the proper equipment to do the alignment you must know what part is the transmit and what is the recieve.

Posted on May 10, 2009

Benimur
  • 6966 Answers

SOURCE: cb problem have a cobra 19dx iv with a 2ft magnet

Hi and welcome to FixYa,

Which output is muffled, transmit (modulation audio) or receive audio?

If you are referring to the receive audio, initially, have you tried an external speaker? If it works good, then it would be an internal speaker problem; if not then others to check would be:

  • IC1 - KIA7217AP audio IC;
  • CM 10 & 15 - audio output capacitors 470uF / 16V.
if it were transmit / modulation audio, try replacing the mic.

Please postback updates.

Good luck and thank you for asking FixYa.

Posted on Aug 01, 2009

steve132003
  • 98 Answers

SOURCE: cobra 19dx iv when i

Just buy a factory built antenna/(it should be close) Buy you a magnet mount RADIO SHACK job(works). If your indoors buy ANTRON A99(set at 1.3 SWR factory). If it keys 9 db then that equals 4 watts output thats OK.

Posted on Apr 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Finals for Cobra 19DX IV...where can i buy them?


cost of finals plus S&H plus labor. cheaper to buy a new one and have that one for parts. H&Y electronics has them but you have to call them to make sure they do.

Aug 22, 2013 | Cobra 19dx Iv Eu Multiband Am Fm Cb Radio...

1 Answer

Need a schematic for a Cobra 19DX IV


don't cut or increase watts.Check it out first as you may want to turn down wattage. Cutting or clipping a radio is not good . over modulation could cause a problem not only with the radio but with those you talk with. You will be slashing your modulation waves over the whole band any if it interfears with them they won't be happy. you can get all the information you want on www.cbtricks.com

Dec 31, 2012 | Cobra 19 DX IV CB Radio

1 Answer

Will a cobra power mic cure the low mod on my cobra 19 dx iv eu or will it blow the front of the rig


that is simply bs, Ham radio shops rarely like CB people (I am a long time cber and also a ham.

On that radio there are two things you can do, look for the mod limiter and remove it or another more simple thing:
This radio comes with a 1000 ohm element in the mic--like speakers---Get a older or new 500 ohm microphone and wire it or have it wired for the 19 dx, it will make a big difference in how it sounds.

I not only worked on those radios but sold them in a shop I owned.

You might find a used mic that's 500 ohm, it is usually stamped into the back case of a mic.

Dec 19, 2012 | Cobra 19dx Iv Eu Multiband Am Fm Cb Radio...

1 Answer

2 out of 5 signal reading on cobra cb radio


You'll need to find another CB radio for someone to check to see if they are receiving your transmission.

Aug 16, 2012 | Cobra 19 DX IV CB Radio

1 Answer

Where is dev pot located Cobra 19dx


its factory set for a reason. being you could be interfearing with someone talking down in the 10 meter band or lower.

Jun 05, 2012 | Cobra 19 DX IV CB Radio

1 Answer

Cobra 19dx iv when i key up it swings all the way to a 9 is there any way to set swr,s without a meter


Just buy a factory built antenna/(it should be close) Buy you a magnet mount RADIO SHACK job(works). If your indoors buy ANTRON A99(set at 1.3 SWR factory). If it keys 9 db then that equals 4 watts output thats OK.

Apr 02, 2011 | Cobra 19 DX IV CB Radio

1 Answer

I Have A Cobra 19dx It Puts Out Good But I Can Only Hear A Short Distande


check the swr's on the antenna. all shops should do it for free just to check them. WE DO here in texas.. but if antenna isn't install properly then it may be high swr causing short distance.

Dec 12, 2010 | Cobra 19 Ultra II CB Radio

2 Answers

How to modify a cobra 19 ultra iii cb


i got a couple of them and i have them talking really good for what they are. if you go inside you can turn up the pods also you can take a small screwdriver and spread those coils inside near the back of cb!

May 11, 2010 | Cobra 19 Ultra II CB Radio

1 Answer

Cb problem have a cobra 19dx iv with a 2ft magnet mount cobra antenna swr is good, receive is good, but muffled output


Hi and welcome to FixYa,

Which output is muffled, transmit (modulation audio) or receive audio?

If you are referring to the receive audio, initially, have you tried an external speaker? If it works good, then it would be an internal speaker problem; if not then others to check would be:
  • IC1 - KIA7217AP audio IC;
  • CM 10 & 15 - audio output capacitors 470uF / 16V.
if it were transmit / modulation audio, try replacing the mic.

Please postback updates.

Good luck and thank you for asking FixYa.

Aug 01, 2009 | Cobra Radio Communications

1 Answer

PEEK IT


not a good idea to do it yourself you need the proper equipment to do the alignment you must know what part is the transmit and what is the recieve.

Apr 10, 2009 | Cobra 19 DX IV CB Radio

Not finding what you are looking for?
Radio Communications Logo

Related Topics:

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cobra Radio Communications Experts

AnyMHz.com
AnyMHz.com

Level 2 Expert

500 Answers

Steve

Level 3 Expert

3287 Answers

Brad Brown

Level 3 Expert

15557 Answers

Are you a Cobra Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...