Question about Frigidaire ATF6000FS Affinity 3.5 Cu. Ft. I.E.C. Capacity Front Load Washer, Electronic Control Panel, Stainless Steel Wash Drum, 7 Wash Cycles, Heavy/Light Soil Options, Tumble Action Cleaning System, 14 Hour Delay Start, Replaced ATF6000ES ATF6000F ATF6000 AT

1 Answer

Parts of the clay

Problem

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Frigidaire Master
  • 17,129 Answers

Did you mean parts for the machine, Click this link: Spares

Posted on Jan 23, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Build up of dirt in tub making clothes dirty... How do I clean inside of machine?


If you use powder detergent ( clay carrier) the build up is from undissolved powder ( clay)
It forms cakes between the spin tub and the outer bowl
The fix is to pull the washer apart and physically remove the caked up mud from all parts of the machine
The prevention of future mud is to use liquid detergents rather than powders
It works like this powder detergents have a small percentage of actual detergent in use and that is dried onto a clay base as a transporter agent
In the wash , the detergent is released but the clay will not dissolve
Most is pumped out with each spin but a certain amount remains , dries and starts the dirt process through the clothes
With liquid detergents there is the same amount of actual detergent but the carrier is water and that is diluted in the spin and completely flushed away

Dec 30, 2015 | Washing Machines

1 Answer

What liquid solution will disolve chalk


If you can't rub the glass because it's coated, try an auto-parts store for solvent to remove the chalk.
If it's bare glass, a razor-blade scraper will do the trick, but don't scrape the tinted/coated side! Or you could use an auto-detailers clay bar - see http://www.wikihow.com/Use-a-Clay-Bar
Good luck!

Jun 25, 2014 | Computers & Internet

1 Answer

How do I get rid of water marks on my mazda 2 roof wrap?


You can try Vinegar or get a clay removal from parts store will remove paint and just about anything the clay will...
or a good cleaner /wax

May 10, 2014 | Cars & Trucks

2 Answers

Concrete tile or Clay tile


clay tiles have little more lifespan than that of concrete. While clay tile is only popular in its red color, concrete tiles are available in wide range of colors.
Clay tiles break easily but concretes do not. But both concrete and clay tiles are the pinnacles of beauty.

Dec 09, 2013 | Washing Machines

1 Answer

Sculpey and firm sculpey tend to crumble even after kneeding


Found this on the Sculpey website- Hope it helps :)

"If your clay is just a little dry or firm, it may only require the addition of Sculpey Clay Softener to reconstitute it (about 6 - 8 drops per 4 oz clay or 2 - 4 drops per 2 oz clay).The Clay Softener will not restore clay once it has become very hard or after it has been baked. If the clay is already crumbly, it has either had too much exposure to heat or old enough to have already undergone some chemical changes. At this stage, it cannot be reconstituted satisfactorily. Adding a pinch of Sculpey MoldMaker to clay that is a little dry or firm will also help reconstitute it."

http://www.sculpey.com/faq-new/209#

Sep 21, 2011 | Sculpey Crafts & Hobbies

1 Answer

I have some roseart modeling clay and I don't have the box it came in. Can it be dried in the oven and if so how do you do it?


You can dry it in the oven:

1. Preheat the oven to 300 degrees F. Remove all pots and pans from the oven. The clay gives off smoke that adheres to the pots and pans.

2. Place the modeling clay on a baking sheet and set it in the oven. Place it on the bottom shelf of the oven to give more room overhead. To prevent the clay from sticking to the baking sheet, place parchment paper on top of the baking sheet. Once you are finished, it is safe to use the baking sheet for cooking again, just wash it off with warm water and dish soap.

3. Wait at least 20 minutes and check on the clay. Touch the Rose Art clay to see if it is still soft. Larger, thicker clay pieces take longer to bake, so if the clay is still soft place it back in the oven

4. Check the clay every 10 minutes until the entire piece is hard. Once hard, remove it from the oven and allow it time to cool.

Hope it helps out!

May 08, 2011 | Roseart Toys

1 Answer

Toilet downpipe


If you live in an older part of Town, You most likely have an older Sewer, 4-6" clay drain tile leaving your house. This Tiles is in 2-4ft clay sections, layed together with concrete and other ("OLD FASHION TECH") You or your neighbor probably have roots in your old clay tiles creating a blockage. The Roots can enter through the cracks between the old joints of the clay tile in search for a great supply of water!!! Your cheapest and best bet is to call a certified roto-rooter company or someone able to use a roto-rooter rental machine. If you need more info, feel free to ask....Joe

Jan 08, 2009 | Home

1 Answer

Clothes are still soaking wet after spin cycle and the wash cycle is complete.


Sounds like your bearings have gone in the back of the drum and damaged your water seal. the clay type substance is possibly water mixed with grease.

Mar 27, 2008 | Maytag MAH6500 Neptune Front Loading...

Not finding what you are looking for?
Frigidaire ATF6000FS Affinity 3.5 Cu. Ft. I.E.C. Capacity Front Load Washer, Electronic Control Panel, Stainless Steel Wash Drum, 7 Wash Cycles, Heavy/Light Soil Options, Tumble Action Cleaning System, 14 Hour Delay Start, Replaced ATF6000ES ATF6000F ATF6000 AT Logo

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1460 Answers

Jason Harris
Jason Harris

Level 2 Expert

264 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...