Question about Sharp LC-32GA5U/LC-32GA5E 32 in. HD-Ready LCD Television

1 Answer

Channel name disappears

For unknownn reaso(perhaps I inadvertently click on a wrong button) the name of the channel and info appears for few seconds on the screen and then disappear.What should I do to have it on the screen at all times?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 326 Answers
Re: channel name disappears

Hello, there should be an info button on the remote. By repeatedly pressing this button you should achieve to have it on the screen constantly. Best regards, Arpi

Posted on Jul 22, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

4 Answers

Lg 42ls575t won't go to "input" screen or "home" screen so cannot select HDMI channel. "Loading" message appears for 30s or so then disappears

1- turn off you router
2-go to settings
3-ok on the ? (support)
4-inatialisation of premium.

Problem solved

Apr 15, 2013 | Flat Panel Televisions

1 Answer

Black rectangle appearing in lower half of screen on 32" Aquos

did you turn off the close caption settings in the set up menu.

Sep 15, 2012 | Flat Panel Televisions

1 Answer

My sony bravia digital channels always drop out of signal. Sometimes a channel has no signal for a couple of weeks. Could that be a fault with the tv?

For tuner problems, especially the digital channels, you should check for a TV firmware update at I was having some strange loss of digital channels on our 40" Bravia, starting with channels only appearing for a second before the screen produced a 'No Signal' message. After we tried the automatic retuning, then we could not even get the one second signal. None of this appeared on the description of the download. However, we downloaded the patch to our PC, loaded the file (19 MB) onto a small flash drive, which we then used to upgrade the firmware in the TV. All our digital tuner problems disappeared!!

Oct 16, 2009 | Sony Flat Panel Televisions

1 Answer

Picture Disappears with in seconds after powered

picture disappear and appear again after few seconds.this is repeated again and agains

Apr 04, 2009 | Hisense TA42P40M 42 in. Plasma Television

2 Answers

Channel information stays on screen for av channels

there should be a info button or display button on remote to turn on and off, unless it is coming from the box that is connected to tv

Jun 02, 2008 | Sony BRAVIA KDL-32S2000 32 in. LCD HDTV

2 Answers

Channel changes automatically

There are a few things that can cause this. #1 most often cause is either something spilled on the channel button or something wrong with the bezel where the buttons are located causing the button to be pressed all the time. Check the buttons on the tv and make sure none of them are stuck. #2 is a bad button (switch). Replace the switch or the control board. #3 is a short on the wiring harness going from the switch to the mian board. Maybe it's squished against the frame somewhere. #4 would be a bad main board. You will likely have to take this unit to a service centre to have it looked at.

Apr 14, 2008 | ViewSonic NextVision N2010 20 in. LCD...

1 Answer


If the lines across the screen are made up of coloured blocks, then the problem is likely to be a weak signal.

Digital channels are broadcast in groups called multiplexes. Sometimes one multiplex may have a weaker signal than others, and so you experience problems with up to 6 channels when all others are ok.

If it is only one or a few channels then just wait and see what happens, because it may be transmitter works.

If you have problems with all channels it could be a connection or antenna problem.

If the lines are just straight lines, then try resetting the TV as follows:

Switch on the TV

Press and hold the menu button on the side of the set. The settings menu will appear. Hold until the menu disappears again.

When you release the button, the TV will take up to about 90 seconds and then reset.

The TV will then show the original screen when the TV was new.

Press ok when shown.

Set language and country settings.

Move down the list and press ok to re-install all channels.

Feb 22, 2008 | Philips 26PF5521D 26 in. HD-Ready LCD...

1 Answer

Cannot change channels in digital mode

Solution that worked for me:

Beware: Although the process should be safe, it technically voids your warranty.

Enter the service menu:
1 - turn of tv with remote
2 - press and release in the following order on the remote: Info, Menu, Mute. Make sure remote is pointing at the tv
3 - turn on the tv from the remote
4 - you will see the service menu. using the down arrow on the remote select the Reset option. Using the right arrow button at this point will do a hard reset.
5 - Wait a few seconds, turn TV on
6 - you will have to rescan analogue and digital channel but it should be working now.

Jan 29, 2008 | Samsung LE26R73BDX 26 in. HD-Ready LCD...

6 Answers

Jvc flat screen television model AV32F713 Black box on screen.

On the reomte control (bottom) left of the sleep button is a cc button, push that until "OFF" appears on the screen. The close caption box should disappear. It worked for me, finally.

Nov 29, 2007 | Sony BRAVIA KDL-46S2000 46 in. LCD HDTV

Not finding what you are looking for?
Sharp LC-32GA5U/LC-32GA5E 32 in. HD-Ready LCD Television Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Flat Panel Televisions Experts

The Knight
The Knight

Level 3 Expert

66552 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Dave Naylor
Dave Naylor

Level 3 Expert

834 Answers

Are you a Sharp Flat Panel Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides