Question about Triumph Academy Sports 400T Treadmill

Open Question

Error 1

Will not run treadmill, keeps showing E1 on speed display

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Merit 725 T plus reading E1


If you wish to get some details about treadmill error codes and repair; check the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

Nov 28, 2016 | Exercise & Fitness

1 Answer

How do i fix a lifegear treadmill 97520?


Try below:

ERROR CODE
DESCRIPTION
E1
Speed error (The treadmill running speed is 3.2 kph faster than the displayed
speed). The treadmill will stop immediately when the console detects this error.
E2
Speed error (The treadmill running speed is 3.2 kph slower than the displayed
speed). The treadmill will stop 16 seconds later after the console detects this
error.
Troubleshooting / Resetting error codes
In the rare event of the treadmill displaying an error code ("E" followed by a number), simply reset
the computer by:
1. Step off the treadmill. Ensure that you are clear of the running belt.
2. Turn the treadmill off at the master power switch located near the motor housing.
WARNING: Ensure nothing is positioned near or under running belt which may possibly block
it's normal operation.
3. Turn the treadmill on at the master power switch.
4. Ensure that the Safety Tether Key is securely and properly installed onto the console or just
reinstalling the Safety Tether Key can also reset the display.
If the above does not clear the error code, please contact the nearest Dealer/Service Center

LifeGear 97320 Owner Manual Page 17

May 22, 2016 | Exercise & Fitness

1 Answer

How long does it take for someone to help me, on this site.


How fast you get answers depends on many factors. I just picked up your question but have spent time finding and reading the manual. I am by no means a treadmill expert, but my first thought was treadmill belt tension was too loose to keep the movement sensor happy.

Moving the belt manually would be irrelevant as the electronics would not be monitoring to throw up the E1 Error..

The manual tells you to check all these things.

E1
Loss of Feedback Speed Sensor disconnected Check Speed Sensor
Connection
Speed Sensor Misaligned Check Sensor position
Faulty Speed Sensor Replace Speed Sensor
Loose Display Connection Check Display Cable
Connection
Faulty MCB (D2 LED on) Replace MCB
Faulty Drive Motor Replace Drive Motor


If BH Fitness are being no help, I would be asking them to take the machine away or get it fixed on-site.

So does the belt turn when you switch it on? Is the belt centrally aligned when it spins?

Page 35 shows belt adjustment and I would guess tension although not specifically mentioned.

http://www.bhfitnessusa.com/manuals/final/ts2.pdf

Jan 05, 2016 | Bh Fitness TS2 Folding Treadmill

2 Answers

I have it all set up..programmed a work out...it starts to work..but the tread itself that you walk on wont run..what do I do?


From the User manual....here
http://servicedocuments.com/pdfs/_0005_SOLE/_0005_SOLE_01_Treadmills/003_OwnersManuals/2010_2011_SOLE/F63_F65_OM_810.pdf

'1.If the belt moves, but stops after a short time and
thedisplay shows "LS", run calibration. (on next page)
2.If you press start and the belt never moves, then
the display shows LS, contact service.

Sep 14, 2014 | Sole Fitness F63 Treadmill

1 Answer

I get an error message E1 on my Athlon model Simplicity treadmill. Belt stops. Any ideas on what this means?


Step 1:

ERR 1 - Motor Movement

ERR1 indicates a speed issue. In this case, the motor speed as reported from the optic sensor differs

from the speed setting.

Analysis: Optic sensor signal issue -- Either the optic sensor signal is not right, or it is read incorrectly, or

the signal is not reaching the display.

Clean the s.speed , test for open or faulty-see the diagram for adjust. tight the connector very well.

God bless you
2_8_2013_11_04_57_am.gif2_8_2013_11_05_17_am.gif

Step 2:

2_8_2013_11_05_40_am.gif

Feb 08, 2013 | Exercise & Fitness

1 Answer

My treadmill showing E1 error code


ERR 1 - Motor Movement

ERR1 indicates a speed issue. In this case, the motor speed as reported from the optic sensor differs

from the speed setting.

Analysis: Optic sensor signal issue -- Either the optic sensor signal is not right, or it is read incorrectly, or

the signal is not reaching the display.

Tes the s. sensor for open or faulty. Clean it + tight the connector very well and try again. see the diagram for adjust.

God bless you
2_4_2013_5_55_36_pm.gif2_4_2013_5_56_02_pm.gif

Feb 04, 2013 | Quantum Exercise & Fitness

1 Answer

Code e1 on my treadmill


please see the indication for error 1. and fix it. see the block diagram
Lube the Deck belt and rollers bearing too.

ERR1 indicates a speed issue. In this case, the motor speed as reported from the optic sensor differs

from the speed setting.

Analysis: Optic sensor signal issue -- Either the optic sensor signal is not right, or it is read incorrectly, or

the signal is not reaching the display

1_1_2013_11_59_40_pm.gif

Jan 01, 2013 | Fitness Equipment Estore Bremshey Scout...

1 Answer

E1 on display


You have 1)probably faulty sensor speed
2) bad connections with sensor speed tight.
3)main motor faulty
4)main motor board faulty.
the error code varies between manufacturer.

However please adjust the speed sensor the magnet with the side of the motor face to face.
Test the main motor if is not hot or not running with enough speed

And after you did that steps, the problem will be in the main motor board.

See the block diagram.
12_6_2011_2_05_23_am.gif

Dec 05, 2011 | Exercise & Fitness

1 Answer

My tunturi treadmill 661f is showing E1 on the


E1 error code : Unplug unit remove motor shroud and check the distance between the speed sensor and the flywheel and ensure that the speed sensor is properly attached to the motor frame. Check also speed sensor connections.
Unplug the electrical cord from the wall outlet and from the treadmill, wait 1 minute and turn the power switch on again. If treadmill recovers to normal operation, you may continue to use the treadmill.
Check the motor brushes either they worn or not sitting properly

May 16, 2010 | Exercise & Fitness

1 Answer

My Tunturi J620P stops and E-1 shows in display


E1 error code : Unplug unit remove motor shroud and check the distance between the speed sensor and the flywheel and ensure that the speed sensor is properly attached to the motor frame. Check also speed sensor connections.
Unplug the electrical cord from the wall outlet and from the treadmill, wait 1 minute and turn the powerswitch on again. If treadmill recovers to normal operation, you may continue to use the treadmill.
Check the motor brushes either they worn or not sitting properly

May 14, 2010 | Exercise & Fitness

Not finding what you are looking for?
Triumph Academy Sports 400T Treadmill Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Triumph Exercise & Fitness Experts

Mike
Mike

Level 2 Expert

59 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Tom Chichester

Level 3 Expert

33294 Answers

Are you a Triumph Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...