Question about Bosch WFMC 3200 Front Load Washer

1 Answer

E02 message We just got our washing machine yesterday and I did two loads fine. Now we keep getting an error message (E02). My husband has check the hoses and lines to make sure there is enough water pressure etc...what they mention in the troubleshooting guide. Any suggestions?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that gotĀ 5 achievements.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.

  • Contributor
  • 51 Answers
Re: E02 message

Error relates to water taking to long to get into machine. Check tap is open fully, water pressure is ok, hoses are not kinked. also check the small filters either end of the inlet hoses (inlet valves as well) as quite often they can clog up especialy on a new install. Regards

Posted on Jul 25, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

How can I delete E02?

Depends on the make and model but an Error code E02 on most washing machines is slow water flow probably caused by a blocked filter! Remove panel on front bottom left or right side and clean filter! Should then clear error itself!

Oct 21, 2014 | Washing Machines

1 Answer

Washer will not run

f06 OR e02 error code means you have an interface communication error. the main control board isn't communicating with the front interface control board. if you pull the washer out and remove the 3 screws coming in from the back of the top panel. the top panel will pull straight back, up, and off. check all the wire connections between the two control board and make sure they are all secure. if everything looks good, then the interface control board may need to be replaced.
f01 e02 means that your motor control board is not reading the tachometer on your motor when it tries to turn the motor. it thinks that the motor is struggling. open the door and turn the basket to make sure it spins freely.

Sep 28, 2014 | Maytag MHW6000XG Maxima High-Efficiency...

1 Answer

Error code F01 E02

For how long did you unplug the power cord? If it was under 5 minutes, unplug it for longer. Check if that clears the error code. If it doesn't, the motor control unit needs to be replaced.

Please double check your model number to get the correct part. Most of the Whirlpool washers have model numbers that start with 3 letters.

I hope this helps.

Cindy Wells

Dec 20, 2013 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Hoover Optima WMH 147 DF water keeps on filling up

have a Hoover OPtima washing machine WMH 147 DF. It is filling up with water and not stopping, also the panel lights and wash cycle time display are not coming on. It's only 1 old

Dec 13, 2012 | Washing Machines

1 Answer

The LF error message pops up on Bravos washer

might want to check screens in fill valve where hoses attach to machine

Apr 23, 2010 | Maytag Bravos MTW6600T Top Load Washer

2 Answers

Dryer was working fine yesterday now the start/pause light flashes and nothing else.


Do you see any Error Message?

Does the machine fill with water?

Does it agitate?

Let me know, so that we could proceed.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Mar 16, 2010 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

After about 5 minutes into a wash cycle, the error "E02" is displayed and the wash cycle stops. What does this error message mean? It isn't in the book that came with the washer.

I just had this problem. My water supply (hot ) had been turned off since my husband used it to fill our hot tub. Other causes were-supply hose kinked,strainers in supply hose clogged, water pressure too low. Hope this solves your problem!

Jan 09, 2010 | Bosch Nexxt 300 Series WFMC2201UC

2 Answers

Maytag MAF 1675 showing an 'Error 2' message

sounds like money, well it might just be money
probably money stuck in the pump

Jun 11, 2009 | Washing Machines

1 Answer

Error message LE5E and would only oparate prewash

it's not on 'test' is it,
try turning the machine on while pressing the start and on buttons together until dOFF apears.

Jan 17, 2009 | Hotpoint Aquarius WD640 Front Load...

1 Answer

E02 Code

Faulty heating element, or main eprom is faulty

Jun 30, 2007 | Bosch Nexxt Premium WFMC6400UC Front Load...

Not finding what you are looking for?
Bosch WFMC 3200 Front Load Washer Logo

1,354 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Washing Machines Experts

Tim Whalen

Level 3 Expert

3056 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers


Level 3 Expert

56836 Answers

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides