Question about SE3010 2003010 Amp Manual Starter and Charger

Open Question

Wiring diagram for schumacher se-5212a

I have only 9.1v output

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Dirt Dobber
  • 253 Answers

SOURCE: Both Battery clips have come off of Schumacher

use a voltmeter. turn on unit to a low setting, place volt meter leads on broken wires one on each. if the voltage goes positive on meter. the positive clamp goes on the wire that the positive(red) voltmeter lead is on and the same for the negative.
Good luck

Posted on Jul 09, 2011

  • 6 Answers

SOURCE: Both Battery clips have come off of Schumacher

You need to connect the battery cable wires to the battery in order for the charger to "turn on" the output. If the "reverse polarity" LED lights up, switch the wires. The RED clamp goes to the + battery terminal wire, BLACK goes to the other.

Posted on Sep 22, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I recently purchased an onkyo tx-nr626 receiver with phono input. When playing albums , I don't get full sound. Sound is clear but not full and loud.


Different cartridges put out various levels based upon their technology - make sure you are using the proper input for their output. A line level input 1V P-P won't work on most phono cartridges and will require a preamp to boost it to the higher level.

Dec 23, 2013 | Technics SL-BD20D Turntable

1 Answer

I recently purchased an onkyo tx-nr626 receiver with phono input. When connected I don't get full sound.


Different cartridges put out various levels based upon their technology - make sure you are using the proper input for their output. A line level input 1V P-P won't work on most phono cartridges and will require a preamp to boost it to the higher level.

Dec 23, 2013 | Technics SL-BD20D Turntable

1 Answer

The outputs on my Pioneer GM-5300T are intermittent and low


yes they are perfect whenever I turn up the bass it just trips on and off

Feb 07, 2013 | Pioneer GM-5300T Car Audio Amplifier

1 Answer

HAVE A MEGALOOP+ hearing aid SYSTEM. THE SOUND FROM A NEW DIGITAL TV IS DISTORTED CAN I ALSO PLUG IN A MICROPHONE TO USE WITH THE NORMAL SCART ATTATCHMENT IF SO WIRING INSTRUCTION PLEASE


I would imagine the level is too high. Does your loop amplifier not have a sensitivity control?
You could come out of the scart socket but check for a headphone volume control first!

The connection standard requires that the pins are utilised in the following manner:


Hope this is useful.

scart.gif PIN USE LEVEL / IMPEDANCE 1 Audio Output (R) 0.5V / 1K-ohm 2 Audio Input (R) 0.5V / 10K-ohm 3 Audio Output (L) 0.5V / 1K-ohm 4 Audio Ground -------------------- 5 Blue Ground -------------------- 6 Audio Input (L) 0.5V / 10K-ohm 7 Blue 0.7Vp-p / 75ohm 8 Status (CVBS) L:0-2V H:10 - 12V / 10K-ohm 9 Green Ground -------------------- 10 Data D2B (Inverted) -------------------- 11 Green 0.7Vp-p / 75 ohm 12 Data D2B -------------------- 13 Red Ground -------------------- 14 D2B Ground -------------------- 15 Red 0.7Vp-p / 75 ohm 16 RGB Status/Fast Blanking L:0-0.4V H:1-3V / 75 ohm 17 CVBS Video Ground -------------------- 18 RGB Status Ground -------------------- 19 Composite Video Output 1V / 75 ohm 20 Composite Video Input 1V / 75 ohm 21 Case Shield ---------------------

A 21 pin SCART cable with all pins connected is wired as per the following diagram:

Jan 23, 2011 | Televison & Video

1 Answer

NO DISPLAY


try to check all components (smps section )

Apr 08, 2009 | SAMTRON 55V 15" CRT Monitor

1 Answer

Do I have Progressive Scan on my TV?


component video is HD of sorts lower end of the scale. Your set has progressive scan..

Mar 26, 2009 | Televison & Video

1 Answer

Red light is on when i connect input cable earthquake 1000w amp


Cables are either shorted, or deck is putting out too much power for input on amp... many new head-units will put out up to 7v on the output jacks (RCA) the amp may only want to see up to 1v will need to consult head-unit manual for adjustment of outputs.

Jan 22, 2009 | Earthquake Sound PH-D2 Car Audio Amplifier

1 Answer

Body of SPF-40-1v


i have a spf40 casio, all is ok but interior display damaged viciorici@gmail.com

Aug 11, 2008 | Casio Sea-Pathfinder SPF40-1V Wrist Watch

1 Answer

ASROCK 845 BIOS PROBLEM


Hi, This problem sounds more like a failing poewr supply than a bios problem. Can you use a multimeter? If so then check the voltage output from your power supply. The red wire = 6v+or-1v. The yellow wire= 12v+or- 1v. black is negative. If you are not sure then try a different power supply. Goodluck mistyman

Sep 14, 2007 | Asrock P4I45GV R5 Motherboard

Not finding what you are looking for?
SE3010 2003010 Amp Manual Starter and Charger Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Schumacher Vehicle Parts & Accessories Experts

Ruben Diaz

Level 3 Expert

514 Answers

treeeee
treeeee

Level 3 Expert

519 Answers

Rigger

Level 3 Expert

1108 Answers

Are you a Schumacher Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...