Question about Kenwood KAC-7204 Car Audio Amplifier

1 Answer

What is briged mode - Kenwood KAC-7204 Car Audio Amplifier

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

I think you mean bridged.Which it is when you have for example a 2 Channel amp but instead of hooking Ch1's + & - or Ch2's + & - to the terminals on your speaker you would instead hook a + from Ch1 then the - from Ch2 to your speaker. The purpose is to increase the rms wattage being delivered to the speaker. Be sure to check what ohm stable your amp is while bridged though cause if the load is to low the amp will not last long.

Posted on Apr 11, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I what to know how would i brige my speakers


if you have two speakers wire them up as usual but run them to only one channel on your amp.

Oct 12, 2009 | Alpine Type-R SWR-1242D Car Subwoofer

1 Answer

Having problems with the installation of the brutus 2008d amp in my truck. how many channels is it? how do i connect the subs? do i connect the rca cables from the radio to the input or output.


The rca cables from your stereo go to the "input" part of the amp. Now, if there are four speaker connections in your amp, then it's a 2 channel. If you have eight speaker connections then you have a four channel amp. Note, some amps can be briged to provide more power to the speakers. On a two way amp(2 speakers), the connections can be briged to only one speker providing more power, usually whatever the amp power rating is, say a 500watt amp will put all 500 watts to that speaker. The same goes for a four way amp(4speakers), can be bridged to two speakers(250watts per speaker). Hope this helps.

Sep 04, 2009 | Car Audio & Video

1 Answer

Engine light is on and sounds as though the rpms are too high


SOME ONE MAY HAVE LEFT THE DIAGNOSTIC BRIGE WIRE CONNECTED OR THE ECU IS FAULTY

Aug 30, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

Problem with mouse and keyboard


you either loosened the cables going to the board for the keybboard and touchpad or have a briged solder joint.

Jul 26, 2009 | Acer TravelMate 2451WLMi Notebook

1 Answer

How do you wire sub speakers to change omes


if you have a 4ohm sub you can series it with another to make a 2ohm load. this is done by + from amp to + on one sub then take the - of that same sub and run it to the+ of the other sub then you only need to run a wire from - of that sub to the - on the amp. NOTE IF YOUR AMP IS BRIGED THIS IS A 1 OHM LOAD!! IF THE TOO SUBS ARE ON ONE CHANNEL THIS IS A Two OHM LOAD IF YOU ARE RUNNING 8 OHM SUBS THEN YOUR AT 4OHM PER CHANNEL AND 2 OHM BRIGED

Jun 13, 2009 | Kenwood KSC-WA82RC Car Subwoofer

1 Answer

York mini split unit has power but will not come on stand-by.


york split ac indor unit no working .timer light is on . how to stope timer control light ?

Jan 12, 2009 | Frigidaire FAA065M7A Air Conditioner

2 Answers

SPL AMPLIFIER


Have you checked to see if your subs voice coils have shorted. That could cause the amp to heat up, on rare occasions the protection lights don't work. Rare, but possible.

Oct 08, 2008 | SPL Phantom DK2-1000 Car Audio Amplifier

1 Answer

780i with two 8800GTX's in SLI mode. What bridge and setup do I use?


It should work if you leave the 3-way on with 1 dangling. You won't fry your PC if it doesn't work, so no worries on that. Try it. Let us know!

Feb 09, 2008 | Computers & Internet

Not finding what you are looking for?
Kenwood KAC-7204 Car Audio Amplifier Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4869 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...