Question about Office Equipment & Supplies

1 Answer

Gear stripped and was replaced. Now the door only goes about a foot then stops and returns. Only goes about a foot either way. How do you repair this problem?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 56 Answers

NAME FOR MANIFACTURE, MODEL NUMBER, CALL TECHN SUPPORT OR CUSTOMERSERVICE, SOME NEW STAPLES STORES MAY BE ABLE TO HELP IF NOT CONTACT ME HERE
CANDYMANGANDY

Posted on Jan 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

NEED TO REPLACE A STRIPPED GEAR


What make and model of Fax machine.????

Sep 05, 2010 | Office Equipment & Supplies

1 Answer

Brother 4750 intellafax it sounds like ait is stripping gears when it strats up


Have you tried another toner or drum cartridge? Most common reason is drum drive gear or fuser gear is cracked. This is a difficult repair job. We charge about $ 90.00 to repair in Clearwater Florida.

May 14, 2009 | Brother Office Equipment & Supplies

1 Answer

Print unable 50


The carrier that goes back & forth has a timing strip ( a plastic strp about 1/4" wide and goes the legth of the machine) If you open the top cover. put your hand in the hole fill twards the front of the machine and the top cover. now the carrier has a U shaped sensore that this strip goes through. 9 times out of 10 the stip has gottin bummped out of position. now you need to put that strip back in the sensore. hard to do with covers on. if look close at the top cover not that hard to take off.
good luck

Jan 07, 2009 | Brother Fax-1360 Plain Paper Inkjet Fax

1 Answer

Printer problem


It sounds like a bad encoder strip (ribbon cable). Uneconomical to repair.

Sep 25, 2008 | Sharp UX B700 Plain Paper Inkjet Fax

1 Answer

Fax machine problem brother 1820c


The ADF rollers may be dirty or may even be damaged. To determine this, 1. Open the transmit door. 2. take a look at the condition and placement of rollers and sensor actuators.3. Using a lintless rag and 99% Isoprpynol, clean the rollers thoroughly. 4. Clean the scanner glass and also the white strip on the transmit door opposite the glass. 5. Do not forget to examine the final roller (paper out roller) This may be damaged or the gear or even the plastic clips that hold this down may be broken. finally make sure that the transmit door can be snapped shut properly.

Jun 09, 2008 | Brother IntelliFAX 1840C Plain Paper...

1 Answer

7150C Error Code #54


This error means your purge unit is not working. Most likely there is a piece of paper stuck in the unit (or other object).

You will have to take the unit apart and check for objects inside that should not be there. Also, check to make sure the excoder strip is seated correctly in the printhead (this is a long clear strip that goes from one end of the unit to the other).

If neither of these fixes the error, then the purge unit would have to be removed, inspected and repaired or replaced.

Feb 22, 2008 | Brother MFC-8220 Fax

2 Answers

Gear making a grinding noise


Not too good news I'm afraid. It sound like the fuser gear has failed. Generally the fuser unit (hot section or hot rollers in the back) need to be replaced. Usually when the gear has worn or failed the fuser rollers are also worn and need to be replaced. The gear can be replaced seperately but is a very risky operation and usually results in parts in the fuser unit falling appart due to age and wear, so it is best done as a unit. If possible do not run the machine as it can cause damage to gears around the fuser unit. The best option is to find out how much a fuser unit and labour to fit would be at your local service centre.

Jan 29, 2008 | Brother IntelliFAX 4100 Laser Fax

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts

kakima

Level 3 Expert

98829 Answers

k24674

Level 3 Expert

7993 Answers

yadayada
yadayada

Level 3 Expert

63990 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...