Question about Exercise & Fitness

1 Answer

York aspire treadmill starts for a second then stops with ER1 fault

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Master
  • 12,223 Answers

ERR 1 - Motor Movement
ERR1 indicates a speed issue. In this case, the motor speed as reported from the optic sensor differs
from the speed setting.
Analysis: Optic sensor signal issue -- Either the optic sensor signal is not right, or it is read incorrectly, or
the signal is not reaching the display.
test the s. sensor for open or faulty, clean it, and tight the connector very well. see the diagram attached.
Test the input voltage motor, if there are the motor need repair
God bless youyork aspire treadmill starts for a second then sto - 1_22_2013_6_08_24_pm.gif1_22_2013_york aspire treadmill starts for a second then sto - 1_22_2013_6_08_58_pm.jpg_mi1_22_2013_6_08_58_pm.jpg

Posted on Jan 22, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

maxtreadmill
  • 832 Answers

SOURCE: the treadmill starts then after a few seconds it

More likely LS= Loss Signal open the motor shroud on the motor their should be a cylindrical shape sensor (magnetic). Plug in treadmill and on the motor control board their should be a L E D (red or amber) by manually rotating the motor you should see that light flicker if it does sensor is good if not replace sensor. Next thing if sensor is good check motor brushes to see if they are mis-align or worn if worn less than 3/8" in length replace them

Posted on Mar 09, 2010

  • 12 Answers

SOURCE: york treadmill

Depending on where you let the smoke out, but I would say yes. Remove the covers, I would look at the lower board first see the blackened areas. But the important question is why did it blow in the first place?

Gerritt
Serving the Twin Cities

Posted on Mar 13, 2009

  • 773 Answers

SOURCE: I have a York z16

LS or L5 error is the speed sensor. Because it is such a vague code I can't just tell you exactly what's wrong with it. I can tell you what it may be.

If you are lucky it's just a fuse. If you have belt movement, it's likely that its just a fuse. If there is no belt movement, it can be a computer failure. the MCB will need replacing.

If you have belt movement and you check the fuse, and its not blown, then the speed sensor is no good and needs replacement.

In most cases its a fuse.

Good luck, hope this helps!

Posted on Oct 25, 2010

jyackle5
  • 8197 Answers

SOURCE: Iam trying to find a

You can get the manual on the link below.

http://cgi.ebay.co.uk/INSTRUCTION-MANUAL-FOR-YORK-ASPIRE-TREADMILL_W0QQitemZ140539057613QQihZ004QQcategoryZ15280QQssPageNameZWDVWQQrdZ1QQcmdZViewItem

Posted on May 14, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My York fitness aspire treadmill stopped working and now it will not come on


If you wish to get some details; check the site linked here. Pull up older posts. Refer treadmill articles.
http://electro-medical.blogspot.com/

May 17, 2016 | Exercise & Fitness

1 Answer

Treadmill not working


Belt speed Loss:

This condition indicates that the speed pickup signal was lost continuosly by during 1 second after the motor successfuly started.Normally indicate a failure of speed pickup or abrupt belt stoppage to due any motor, wiring,or motor controller failure.

Oct 24, 2011 | York Barbell Home Use Fold-Up Treadmill

1 Answer

I have a York evolution tv treadmill model x8 which starts for about 3 seconds then stops with E7 on the display, I understand this is a safety key error code but the key is in place and if it's...


Definition: Incline motor calibration abnormality: 35~40 seconds after the down command was sent,
the calibration base signal was not received.
Check the calibration motor (mechanical +electrical)

Jul 11, 2011 | York Barbell Home Use Fold-Up Treadmill

2 Answers

York 2750 treadmill: How do I reset distance display? regards


Does anyone know where I can buy a replacement earlip pulse monitor for York 2750 treadmill?

Jun 27, 2011 | Health & Beauty

Not finding what you are looking for?
Exercise & Fitness Logo

Related Topics:

446 people viewed this question

Ask a Question

Usually answered in minutes!

Top Exercise & Fitness Experts

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Sportsmith LLC
Sportsmith LLC

Level 3 Expert

914 Answers

Tom Chichester

Level 3 Expert

34188 Answers

Are you an Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...