Question about Fujitsu Siemens PRIMERGY C200 Server

1 Answer

Is it possible to repair the power supply of fujitsu c200 server?

Posted by on

  • lcasellar Jan 27, 2009

    if power supply failed. check main resistors of power supply.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 77 Answers

Anything is possible if you have the expertise and skills. However, it becomes a question of Value. Is it worth the several hours of your time to trace down the faulty part and replace it?

Posted on Feb 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to repair ca01022-0550 power supply ?


If you dont have a circuit diagram it is just playing around without knowing what to do or what you are doing! It is trial and error.
If your time is worth a few bucks - buy a new one. You will spend a lot of time without knowing if you did it right and did everything necessary. If you can not get a new one:
Be careful! Do not connect power while case is open!
What does it do? Is your fault current protection switch turning off? Look for capacitors from the live wires to ground.
If just nothing is happening - look for fuses.You can also look for traces of "burning" from loose contact or bad solderings - fix them. You can also look at the electrolytic capacitors. If their top is not flat, but bent, change them. - Karl

Aug 04, 2014 | Fujitsu 275w Model Ca01022-0550 Power...

1 Answer

How we can switch on CA01022-0550 power supply ?


Unlike a PC Power Supply, this type of server power supply does not have an on/off switch. It will turn on when plugged into a compatible server and plugged into a power source. The server itself will power on either with the power button on the front, or when the power supply is plugged in depending on your BIOS settings. Usually there is an LED on the back of the power supply which will come on when the cord is plugged in regardless. If it does not, the unit is defective.

Aug 04, 2014 | Fujitsu 275w Model Ca01022-0550 Power...

1 Answer

I have problem of permenent magnet motors i observed gap in rotor plates two places througout total daimeter its harmful to motor


You need to explain better where the gap is. Most motors do have a gap and it is on purpose. Unless it is a piece missing where the brushes contact. then its bad.

Apr 22, 2010 | Fujitsu Siemens PRIMERGY C200 Server

2 Answers

No display cpu fan are'nt running though there is green and orange light on server


Hello there,

Check your power supply and see if its functioning.

CPU fan that does not run means there is no power getting into the motherboard.

Thank you for using Fixya

Apr 06, 2009 | Fujitsu Siemens PRIMERGY P200 Server

1 Answer

Is it possible to repair c200 power supply


Fujitsu C200 has very precise power supply. And it is always recommended to buy new one.

Jan 27, 2009 | Fujitsu Siemens PRIMERGY C200 Server

3 Answers

Poweredge 2600 power supplies in red


Possibly a power distribution board problem.
PDB requires replacement.

Jul 09, 2008 | Dell PowerEdge 2600 Server

2 Answers

Booting probleam


Hi FAYU,
First make sure that the monitor is plugged into power and properly connected to the tower. If it is, does it sound like the server is actually powering up even though you are not getting display? If the server is powering up, then I would suspect the monitor to possibly be faulty. You can troubleshoot this by attaching another monitor.
If the server is not powering up, then you may have a faulty power supply or faulty processor.
--RoadHawk

Nov 20, 2007 | HP Compaq ProLiant ML110 G4 Server

1 Answer

Error on system start


your system is failing it's Power on Self Test (known as POST) the beeps are a code which tells you where it is failing. unfortunately the codes mean different things for different motherboards, however common faults include Graphics card fault (try reseating) and Memory failure. If you look at the Manaul for the tx300 S2 there is a section on the diagnostic LEDs, I suggest you have a look, as it may help to diagnose your problem (it can identify faulty components) http://manuals.fujitsu-siemens.com/serverbooks/content/manuals/english/thb-d1899-d2099-en.pdf

Sep 11, 2007 | Fujitsu Siemens PRIMERGY TX300...

1 Answer

Primergy c200 no booting


Fujisu Web site Tech Support Team will be able help on this

May 22, 2007 | Fujitsu Siemens PRIMERGY C200 Server

Not finding what you are looking for?
Fujitsu Siemens PRIMERGY C200 Server Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fujitsu Computer Servers Experts

Gareth Cockram
Gareth Cockram

Level 3 Expert

657 Answers

Jax Planet
Jax Planet

Level 2 Expert

921 Answers

tony wahlman
tony wahlman

Level 3 Expert

779 Answers

Are you a Fujitsu Computer Server Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...