Question about Computers & Internet

2 Answers

I can't log in the admin panel of my new Tenda 3G622r+ router using my windows 7 desktop?

It returns "webspage is not available".

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Thanks everyone for the help, but all your solutions didn't solve the problem...the good thing is, I found the exact solution by deselecting "Predict network actions to improve page load performance" in the Privacy section of my Google Chrome Browser.

Posted on Jan 24, 2013

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 7,627 Answers

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Joed911
  • 4338 Answers

SOURCE: Dynex DX-E401 Router setup

Here is the manual, and it states that to get into the router you use admin as the user name and password is blank. I would suggest that you reset the router. The reset button is on the back next to the power connector. Use a paper clip and push the reset button in for about 30 seconds till the lights flash. Then you should be able to log into the setup page and set it up .
http://www.dynexproducts.com/skins/skin_1/Topics/Documents/DX-E401_Installation%20Guide.pdf

copy and paste the complete link into your browser.
If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

Posted on Dec 15, 2008

  • 27 Answers

SOURCE: i can't log in my router to config it..

its not actually a problem, all u have to do is to manually restart ur router and try again with the user name admin and with the password 123456 or 1234. hope it solves ur problem.

Posted on Apr 07, 2009

  • 10 Answers

SOURCE: can't configure router

If you reset the router to factory default and use admin and no password you should get it or sometimes admin and admin for password as well or check the manufacture website to find out what is the default user name and password for that model

Posted on Apr 29, 2009

Dissolu
  • 221 Answers

SOURCE: LOGIN FAIL

at the back of the router is a tiny hole, so while router is on and working push the paperclip or something inside and hold for at least 10secs. This step will reset the router to factory settings and you'll be able to login again

Posted on Aug 01, 2009

  • 8 Answers

SOURCE: Is there any other way to reset the default

If you isp is Consoidated Communication

username admin
password cciadmin

Posted on Feb 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is the login password en tenda router


Defaults for your router are:

Username:Admin
Password: Admin

If you have changed this you may need to hardware reset your router

Jul 18, 2014 | BestPriceCables Tenda 3G622R 300Mbps...

Tip

How to Reset Windows Server 2008 Password Easily?


According to Microsoft, Windows Server 2008 is an award-winning system that allows IT professionals more reliability and flexibility with their server infrastructures. The newer Windows Server 2008 R2 utilizes much of the same coding as Microsoft Vista and features advanced virtualization tools, Web resources and management enhancements. Additionally, the system's Windows 7 integration helps to save both time and money, and provides a platform for a dynamic and efficiently managed data center. Tools such as Internet Information Services version 7.5, Server Manager and Hyper-V platforms, and Windows PowerShell version 2.0 give customers greater control. Often, though, it's simple tasks like resetting a user password that keep IT administrators busy on a day-to-day basis.<br /> As long as you have administrator-level access to your Windows Server 2008 machine, <a href="http://www.passwordunlocker.com/knowledge/reset-domain-password.html">resetting Windows Server 2008 password</a> becomes a quick task once you know where to look.<img src="trans.gif" /> Step 1: Log into the Windows Server 2008 administrator account using the current password.<br /> Step 2: Click the Windows "Start" button, select "Control Panel," and then click "User Accounts."<br /> Step 3: Click "Add or remove user accounts," and then click "Continue" when prompted to confirm your choice.<br /> Step 4: Select the administrator account and click "Change the password."<br /> Step 5: Type the current password in the "Current password" field, type the replacement password in the "New password" field, and then confirm your choice by typing it again in the adjacent "Confirm new password" field.<br /> Step 6: Click "Change password<br /> Well, if you have not the admin level to access or you forgot Windows Server 2008 password, what would you do? Here,<b> <a href="http://www.passwordunlocker.com/windows-password-recovery.html">Windows Password Unlocker Enterprise</a></b> allows you to use a bootable CD/DVD or USB flash drive to <b>reset Windows 2008 admin password </b>in 4 simple steps.(Take USB falsh drive for example).<br /> <b>Step 1: </b>Download and install <b>Windows Password Unlocker Enterprise</b><br /> <b>Step 2: </b>Burn a bootable USB flash drive<br /> <b>Step 3:</b> Set BIOS to boot from USB flash drive<br /> <b>Step 4:</b> Reset Windows 2008 admin password<br /> There are 2 options for you if you need to reset Windows Server 2008 domain pasword.<br /> <b>Option 1:</b> Reset the default administrator password to <b>Pu12345</b><br /> <b>Option 2:</b> Create a new specified account to reset lost administrator password.<br /> If you choose option 1 to reset Windows 2008 Domain admin password, you can log on your computer with the username of <b>administrator</b> and password of <b>Pu123456</b>. If you select option 2 to <a href="http://www.passwordunlocker.com/knowledge/reset-domain-password.html">reset Windows 2008 Domain password</a>, you can log on computer again with the username of <b>unlocker</b> and password of <b>Pu123456</b>.<br /> <br /> <br /> <br />

on Jun 20, 2011 | Computers & Internet

1 Answer

How to install tenda wireless router


Plug in the router and connect it to your computer via a WIRED connection. Connect the cable into the Tenda router in one of the yellow ports labeled 1-4 (which one specifically should not matter).

Open a web browser and go to http://192.168.0.1.

When prompted for a username and password, enter "admin" for the username, and "admin" for the password.

Click "WLAN Settings", then "Basic Settings".

Click "Enable Wireless" if it is not already checked, and enter a new name for your router in the field labeled "SSID". The default name is "Tenda", but you can choose any network name you like, so long as it is made up of only letters and numbers. Leave all other settings on this page at their defaults, and click "Apply".

Now, click "Security Settings".

In "Security Mode", choose a network security type and enter an appropriate password. For demonstration settings, choose "WPA Personal". Make sure "AES" is selected, and then enter in a pass phrase. This will be the password for your wireless network, so be sure to write it down. The default is "PlsChangeMe", so go ahead and change it now. Leave the "Key Renewal Interval" field at its default setting, and click "Apply".

Click on "WPS Settings".

Click "Disable", and then click "Save".

Click "System Tools", then "Change Password". If you want, change the username and password here. You will need to enter the new username where it says "admin", then the old password of "admin" in the Old Password field. Then, enter your new password in the "New Password" field, then again to confirm it.

Close out of the Tenda configuration page.

You have successfully set up your home network. When ready, connect your modem to the router using the blue "WAN" port on the back of the router, and powercycle your modem and router, and internet will then be available on your home network.

If you need any kind of technical assistance you can contact support cell at http://www.vtechsquad.com/

Jan 29, 2013 | Computers & Internet

1 Answer

Trying to set new password for tenda wireless router


you need to access the router's GUI page to change the security key of the routers/
remember, once you change the security key, it should be changed in all the devices you got connected wireless.
you can access the GUI page by typing either 192.168.0.1 or 192.168.1.1 (most of the routers have this default setting) in address bar of internet explorer.
you can find the exact numbers by going to start>run>type "cmd">type "ipconfig">enter
you will see the default gateway number which is the one you need to type in a address bar of the internet explorer. (these steps work only if you get the computer connected with the Ethernet cable first to the router)
once you access the gui page, you have an option to change the wireless key under wireless section>security.
need to mention that when you access the GUI page, you will be welcomed by a username and password log in option. the default username and password again is admin in most cases. if it doesn't work ,check with the manual of the router you got.
if you still need more clarifications or steps on this, please reply to the post.

Apr 01, 2012 | Port Designs Tenda W307R-103421 Router

1 Answer

Im using a tenda wireless broadband..my problem is i cant get the right pre-shared key pls help


Reset your router back to it's factory settings by holding the reset button for about 5 seconds. I have provided a list of the most popular router brands. If it does not work you may need to google what your specific model's default IP address/default username/default passwords are, for example search for "Encore ENHWI-2AN3 default IP address" The default login info can change, it can depend on where you obtained your router. If you purchased it yourself from a store then the standard defaults should work. If you obtained your router from your Internet Provider you may need to contact your service provider. It also may depend whether it's an old or new model router as well. And you may need to press and hold the reset button on your router several times before it actually clears. Make sure you have a wired connection then once you have accessed your router simply run the Setup Wizard. Set your SSID as something you'll remember like "Mavericks Network" and your Password can be something like your phone number for example 3109876543

Belkin - Username: Leave the field blank Password: Leave the field blank Default IP address is: 192.168.2.1

Buffalo - Username: root Password: Leave the field blank Default IP address is: 192.168.11.1

D-Link - Username: admin Password: Leave the field blank Default IP address is: 192.168.0.1

Encore - Username: admin Password: admin Default IP address 192.168.1.1

Linksys - Username: admin Password: admin Default IP address 192.168.1.1

NetGear - Username: admin Password: password Default IP address will be: 192.168.0.1 or 192.168.1.1

TP-Link - Username: admin Password: admin Default IP address 192.168.1.1

TrendNet - Username: admin Password: admin Default IP address 192.168.10.1

Zhone - Username: admin Password: admin Default IP address 192.168.1.1

Zyxel - Username: admin Password: 1234 Default IP address 192.168.10.1

Sep 07, 2011 | TP-LINK Tenda W311R WirelessN Router AP...

1 Answer

I have a linksys wireless g device,it was windows XP setup disk, now i upgrade to windows 7,but i failed to setup my wireless g? where can i have the windows 7 setup supports?


Linksys claims that all or their routers are compatible with Windows 7. You don't need the CD to setup the router. Open your browser and type in : 192.168.1.1
In the pop up box, leave the username blank and type in "admin" (without the quotes) for the password. Or use the username and password that you may have configured at an earlier time. Usually you can just select "setup" in the left sidebar and go from there.

You may have to do a hard reset on the router. Look for a very small button on the router, usually on the side or back. Press the reset button with an ink pin or similar object while the router is powered ON until the lights start flashing. The router is now returned to factory settings, like it just came new out of the box.

If you are having trouble go here: http://homesupport.cisco.com/en-us/wireless/lbc/WRT54G
to download the user guide for your router. If you turn the router over you will see a sticker that has the model number and version. You'll need the version # to get the correct user manual.It will give you the info you need to setup the router.
Also, if you are still having problems, it may be that the wireless adapter is not compatible with Windows 7. You will need to go to the manufacturer's website and download the Windows 7 drivers (IF they are available.)
Please post back if you need further assistance.

Sep 04, 2011 | Linksys Wireless-G WRT54G Router

1 Answer

I cannot connect "wireless" with my TENDA model


TENDA model W268R default IP 192.168.0.1 username: admin password: admin

Reset the Router and reconfigure again....

Jul 04, 2011 | Computers & Internet

1 Answer

How do i set up password to keep anyone from using my wireless connection


Turn the unit on and open a browser window on your computer. Be sure that you've selected the Name of the router, default is linksys, as the network that your computer is connected to. Browse to the Admin page of the router by typing in its IP address, default is 192.168.1.1. You should see a logon screen. The unit should ship with a default password, which is admin. That is, you leave the username field blank and type the word 'admin' (no quotes) into the password field. (Once you are logged in, you can change the password for logging into the router thru Administration --> Management. You should see a two boxes to verify the new password that you would like to create.) For creating a password for the secure Wireless connection, go to Wireless --> Wireless Security. To set up the Wireless security, tho, I think you'll have to connect with an ethernet cable. You can then walk thru the setup. Use WPA2 as the security, if possible.

Jun 17, 2011 | Linksys Wireless-G WRT54G Router

1 Answer

How to instal 3g611R Tenda router


You do have to install any drivers for a "Router", to link your modem & PC to access the internet you just have to configure the router's settings.

Read this link @ How do I configure a Tenda router?
3G611R Default IP:192.168.0.1
3G611R Default Password:admin
3G611R Default Username:admin

Hope it helps.

Apr 08, 2011 | Computers & Internet

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...