Question about Vacuums

Open Question

How to change belt on hoover vacuum series b 7.2

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
reddevil6
  • 1673 Answers

SOURCE: Belt Replacement

Take the bottom plate off, the brush roll and belt are there. the belt goes around the brush roll and hooks to the motor shaft. If you can't get to the motor shaft, then you will nee to remove the top cover also.

Posted on May 13, 2008

Ad
Agent Don
  • 310 Answers

SOURCE: installing belt on hoover self propelled upright vacuum

http://geeksquad.fixya.com/ThreadView.aspx?prdid=40544&thid=641399
Installing belt on Hoover self propelled upright...
Posted by Fryeburger on Jun 02, 2008
Need help installing belt on Hoover self propelled upright vacuum

Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. Hoover Ultra U6430-900 Wind Tunnel Bagged Upright. The best way to install the belt on a Hoover to replace one or both of the belts @ the same time for the best cleaning. The average belt change is every 4 to 6 months for best results. There is a tool that looks like a screwdriver that has a right or left angle on the end that serves as a belt puller and to hook the belt(s) onto the brushroll 1st and then take your puller and then pull or stretch the belt onto the motor pulley. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

http://www.hoover.com Telephone
Contact our Customer Service Department at 1.330.499.9499
Monday through Friday
8 a.m. - 7 p.m. EST

http://www.a-1vacuum.com/ 1-800-657-1874 Customer Service
Thanks, Don the Vac Man
Go Ahead. Use Us.

Posted on Jun 02, 2008

Vac Belts
  • 701 Answers

SOURCE: how do I change the ******** belt in a Hoover

Here is a link where you can view the manual:

Hoover EmPower Manual and Belts

Posted on Dec 02, 2009

Vac Belts
  • 701 Answers

SOURCE: how to change a belt on a hoover turbopower 1700

You can get the replacement belt you need and view the manual with instructions here:

Hoover U5046-930 Belt and Manual

Posted on Dec 06, 2009

VacuumRepair
  • 438 Answers

SOURCE: I have hoover WindTunnel Self Propelled Vacuum

Greetings from GoVacuum,

Here's a great video repair tutorial that we've put together to try and help you with the repair on your Hoover WindTunnel. I hope that this helps you with your repair. If you found this solution helpful, please rate this repair video by clicking on the 4 Thumbs Up Icons in the top right hand corner of my repair solution. Feel free to email me at chris.jones@govacuum.com if you have any questions about the repair!

Video Repair of Hoover Windtunnel Belt Change


Thank you very much!

Chris Jones
GoVacuum.com

Posted on Mar 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you use a Bissel 6594 Series vacuum belt on a Hoover UH71003 vacuum?


yes. The hoover belt is only slightly longer but it shouldn't cause a problem.

Oct 18, 2013 | Hoover Elite Rewind Pet Bagless Upright,...

1 Answer

Removing beater bar from Hoover canister vac sweeper head


click here > http://hoover.com/file/402/ for the manual it will give you full instruction on belt change on page 7

Jan 08, 2013 | Hoover S3765-040 WindTunnel Bagless...

2 Answers

Change belts on a Hoover Power Drive Wind Tunnel Series 900 vacuum


Try calling Hoover directly toll free at
1-800-944-9200 M-F 8 AM - 7 PM EST.

Sep 08, 2009 | Hoover U6437-900 / U6439-900 Windtunnel...

1 Answer

Need to change a belt on my Hoover Concept One Power drive


http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=766023
Generic problem for all Vacuums
Need to change a belt
Posted by gentilly on Jul 10, 2008
Need to change a belt on my Hoover Concept One Power drive

Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. On the Hoover Concept One Power Drive Upright vacuum there are 2 belts, a drive belt and a power drive belt, always use the Hoover genuine belts and for the best cleaning always change you vacuum belts every 4 to 6 months for the best cleaning. !st, remove the bottom plate and cut off the old belts – then you need to lift up the one side of the brushroll that has the pulley side for the longer of the 2 belts and slide it on. Replace the brushroll, B4 you go to far remember which went on 1st, the power drive belt (smaller belt) or the brushroll belt, in either case hook the belt(s) onto the pulley 1st and then use a belt puller or a screwdriver with a hook or bend on the end and stretch the belt(s) onto the motor pulley and then track the belts in a straight line – do this on both belts. Once you have done this then replace the bottom plate. Check your owner’s manual in the trouble shooting guide to see if they also have suggestions or check with your local vacuum cleaner dealer in your area or contact the Hoover website or the Hoover factory cust serv phone # listed below. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

http://www.hoover.com Telephone
Contact our Customer Service Department at 1.330.499.9499
Monday through Friday
8 a.m. - 7 p.m. EST

Thanks, Don the Vac Man
Go Ahead. Use Us.

Jul 10, 2008 | Vacuums

1 Answer

I USED MY HOOVER 3 TIMES...THE BRUSHES DO NOT ROTATE.


http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=724631
Generic problem for all Vacuums
I USED MY HOOVER 3
Posted by ROEHL1 on Jun 30, 2008
I USED MY HOOVER 3 TIMES...THE BRUSHES DO NOT ROTATE.

Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. The best thing if the brushes are not rotating is to change the belt on the vacuum because the factory belt sometimes can be stretched out and or the belt could have broke and needs replacement. If the vacuum is less than one year have them check the brushroll / belt to see id the brushroll make be defective and might be possibly be covered under a Hoover factory warranty. The belt change should be done every 4 to 6 months for the best cleaning and to use the genuine belts for the best cleaning. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

http://www.hoover.com Telephone
Contact our Customer Service Department at 1.330.499.9499
Monday through Friday
8 a.m. - 7 p.m. EST

Thanks, Don the Vac Man
Go Ahead. Use Us.


Jun 30, 2008 | Vacuums

3 Answers

Need a replacemnet belt for upright hoover durabrand


http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=723179
Generic problem for all Vacuums
Need a replacement belt for
Posted by madasalorry on Jun 30, 2008
Need a replacement belt for upright Hoover durabrand

Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. The best place to get a replacement belt for a Hoover DuraBrand vacuum is to contact your local vacuum cleaner dealer in your area or to contact the factory @ Hoover listed below and call cust serv and they will direct you to the parts dept. but, please use the genuine belts instead of replacement belts and the average belt change for flat belts is every 4 to 6 months and if it is a geared belt than once a year for the best cleaning. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

http://www.hoover.com Telephone
Contact our Customer Service Department at 1.330.499.9499
Monday through Friday
8 a.m. - 7 p.m. EST

Thanks, Don the Vac Man
Go Ahead. Use Us.

Jun 30, 2008 | Vacuums

1 Answer

I need to change the belt on the hoover preferred 16.0 how do I open it up?


http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=683113
Generic problem for all Vacuums
I need to change the
Posted by catch100681 on Jun 18, 2008
I need to change the belt on the Hoover preferred 16.0 how do I open it up?

Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. There are only 2 ways in order to change the vacuum belt on a Hoover vacuum cleaner. There should be a couple of levers or screws on the bottom of the vacuum. Once you remove the screws and or the bottom plate the belt should be exposed –if not then the top cover of the vacuum will come off and then you can service it from the top of the vacuum. The average flat belt change is every 4 to 6 months for the best cleaning and to store the extra belts in a Ziploc bag in the refrigerator, for some reason if the belt is a geared belt then you would change it once year. If you have a question look inside your owners manual or to contact your local vacuum cleaner dealer in your area. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

http://www.hoover.com Telephone
Contact our Customer Service Department at 1.330.499.9499
Monday through Friday
8 a.m. - 7 p.m. EST

Thanks, Don the Vac Man
Go Ahead. Use Us.




Jun 18, 2008 | Vacuums

1 Answer

Installing belt on hoover self propelled upright vacuum


http://geeksquad.fixya.com/ThreadView.aspx?prdid=40544&thid=641399
Installing belt on Hoover self propelled upright...
Posted by Fryeburger on Jun 02, 2008
Need help installing belt on Hoover self propelled upright vacuum

Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. Hoover Ultra U6430-900 Wind Tunnel Bagged Upright. The best way to install the belt on a Hoover to replace one or both of the belts @ the same time for the best cleaning. The average belt change is every 4 to 6 months for best results. There is a tool that looks like a screwdriver that has a right or left angle on the end that serves as a belt puller and to hook the belt(s) onto the brushroll 1st and then take your puller and then pull or stretch the belt onto the motor pulley. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

http://www.hoover.com Telephone
Contact our Customer Service Department at 1.330.499.9499
Monday through Friday
8 a.m. - 7 p.m. EST

http://www.a-1vacuum.com/ 1-800-657-1874 Customer Service
Thanks, Don the Vac Man
Go Ahead. Use Us.

Jun 02, 2008 | Hoover Ultra U6430-900 WindTunnel Bagged...

2 Answers

How to change the belt on a Hoover High Performance upright vacuum cleaner


Generic problem for all Vacuums
How to change the belt
How to change the belt on a Hoover High Performance upright vacuum cleaner

I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure.
Most of the Hoover upright vacuums service from the bottom and to start remove the bottom plate, that should expose the belt – if this is the case, some Hoover’s might be self propelled, if not the self-propelled vacs have 2 belts and the non self propelled models have one belt – so remove the belt(s) and then lift up on the brushroll and slide the belt onto the belt pulley then take a screwdriver tool with a hook on the end and stretch the belt onto the motor shaft – once this has been done the track the belt(s) and it should straighten out and run straight, re-install the bottom plate, plug in and test. If you cannot get @ the belt from the bottom the look for 2 or 3 screws – remove the screws and the top cover will lift off and then follow the procedure mentioned above… Questions? Please feel free to contact your local vacuum dealer in your area or in the yellow pages or contact the Hoover factory for more details.
http://www.hoover.com Telephone
Contact our Customer Service Department at 1.330.499.9499
Monday through Friday
8 a.m. - 7 p.m. EST

Apr 22, 2008 | Vacuums

Not finding what you are looking for?
Vacuums Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vacuums Experts

AskDyson
AskDyson

Level 3 Expert

2572 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18402 Answers

D. Floyd Kolb
D. Floyd Kolb

Level 3 Expert

43501 Answers

Are you a Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...