Question about Maytag 30" Built-In Single Electric Wall Oven - Black

1 Answer

Maytag wall over MEW5530BCB

Display panel is flickering slightly dimly and clock won't keep time.

Posted by on

  • lselway Jan 26, 2009

    Yeah..it happened after we had a power failure. Once the power came back on, this was the issue.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

Usually this turns out to be a problem with the main clock/electronic control but the only way to know for sure is to do some electrical testing with a volt/ohm meter and the wiring diagram located within the appliance. If possible use the meter and the wiring diagram to check input/output voltages looking for discrepancies between the diagram and the actual meter readings.


TheRepairGuru ----- www.repairclinic.com


http://www.repairclinic.com/Maytag-Range-Stove-Oven-Parts

Posted on Jan 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Control panel


The error code shown on the display is"Sab", not "5ab".

To disable the Sabbath mode push and hold the Clock pad for 3 seconds.

Jun 18, 2013 | Maytag 30" Built-In Single Electric Wall...

1 Answer

DIM DISPLAY ON GE PROFILE WALL OVEN


when they are dim like this,it needs replacing as its a driver chip that drives the readout and illuminates it you can send in the board for rebuild or purchase outright,as they dont supply any component specs to repair the control panel

Feb 03, 2013 | Ovens

1 Answer

The oven won't turn on. We are unable to set the clock either. The display flickers but doesn't display.


There are lots of different timers on fisher and paykal The last one I reset was a few weeks ago it involves pressing 2 buttons at the same time I think it was the oven on and oven off buttons but I am not sure You will know when you have pressed the right 2 buttons the display will stop flickering set the clock time using the up down arrow buttons The auto light should not be on if it is press the manual button Regards Geoff Stove Recyclers

May 29, 2011 | Fisher Ovens

1 Answer

The digital control display is extremely dim


your model should be a jjw9527AAW.... usually when that clock assembly goes dim u must replace that clock ... for your model it is a part number #71003424.. that clock on sears.com is for sale at $186.06.. call around or shop around for a bettter price remeber shipping charges through sears though and prob take longer to get ahh nevermind ur call...ohh yea kill the power before servicing or call for service... hope this helps take care

Jan 28, 2010 | Jenn-Air 27 in. Electric Single Wall Oven...

1 Answer

MY 24 INCH BUILT IN SINGLE WALL OVEN DIGITAL TIMER


turn power off at main box the back on retry st set clock . if it won;t set / replace it . it has gone bad .mm

Dec 09, 2009 | Maytag 24" Built-In Single Electric Wall...

2 Answers

Oven digital lighted display is dim


You need to replace the C3 capacitor on the control board

http://fixitnow.com/wp/2009/01/28/cheap-fix-for-a-dim-display-on-an-oven-control-panel/

You can replace only the C3 - it is 68uF / 35V and you can go to Radio Shack and get their part # 272-1028 - 100uF/35V one. It takes all but 10 minutes to re-solder the new one in place

May 31, 2009 | Jenn-Air JJW8530C Expressions Collection...

1 Answer

My clock and temperature display is dim


Hi, this will happen over a period of time and its just heat related. the control panel isn't insulated properly and , there has been a larger than normal transfer of heat to the inside of the control panel where the circuits are housed.

If this is a problem, i recommend replacing the control board. it will fix the dim issue.

May 22, 2009 | Jenn-Air JMW9527C Electric Double Oven

1 Answer

My Jenn Air Electric Wall Oven Control panel lights have gone out


You will need to replace the display assbly.
It is a very common problem with maytag/Jenn Air

Feb 19, 2009 | Jenn-Air 27 in. Electric Single Wall Oven...

2 Answers

Oven digital lighted display is dim


mY 27" WALL jENN air blows cold air out the vents when on cleaning cycle. The red buttons aren't lighted. The door locks, otherwise it bakes fine. I wonder if it is really cleaning?

Feb 16, 2009 | Jenn-Air 27 in. Electric Single Wall Oven...

Not finding what you are looking for?
Maytag 30" Built-In Single Electric Wall Oven - Black Logo

213 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Ovens Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Maytag Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...