Question about Insignia LCDTV26 26 in. Television

2 Answers

Removing the stand on Insignia LCD 26F TV

I am trying to wall mount the TV. I cannot remove the stand, Is there a method to do this.

Thanks,

Roger Bird

Posted by on

  • tri1 Feb 01, 2009

    Received no instructions when purchased the tv. Want to remove the stand.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My insignia 26 inch dvd combo TV stand can be removed by removing the access cover to your input connection. There are eleven black phillip-head screws. The three bottom screws also hold the plastic base cover in place. Remove all eleven screws and pull the stand out from below. The four philip-head screws on the back center of the TV is for the location of the wall bracket mount. Good luck.

Posted on Feb 11, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Usually there is four to six screws to take out. normally located on the back of the tv towards the bottom. the manual has labled which screws to take out. make sure you find the center of the stud and put your lag bolts in it. dont use sheetrock anchors or mollys. the tv will eventually fall off the wall. always use the load barring studs.

Posted on Jan 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Try to mount TV to the wall and need to release the TV stand


To Display your LCD TV using a Wall Bracket:

If you decide to wall mount your LCD TV, always use a ULlisted wall bracket appropriate for the size and weight of the LCD TV: 32HL37/32HL37U/32HL17/32HL17U: 38.6 lbs (17.5 kg)

37HL17: 46.3 lbs (21.0 kg)

42HL17: 59.5 lbs (27.0 kg)
1) CAUTION: Two people are required for installation.

2) Unplug and remove any cables and/or other component connectors from the rear of the TV.

3) Follow the instructions provided with your wall bracket. Before proceeding, make sure the appropriate bracket(s) are attached to the wall and the back of the TV as described in the instructions provided with the wall bracket.

4) After attaching the appropriate bracket(s) to the wall and the back of the TV, remove the pedestal stand from the TV as described below.


Removing the Pedestal Stand

1) Carefully lay the front of the unit face down on a flat, cushioned surface such as a quilt or blanket. Leave the stand protruding over the edge of the surface. Note: Extreme care should always be used when removing the pedestal stand to avoid damage to the LCD panel.

2) Remove the jack pack cover on the back of the TV to expose the pedestal stand screws. The jack pack cover can be removed without tools.

3) Remove the five screws. This will allow removal of the pedestal stand.

4) Once you have removed all five screws holding the pedestal stand in place, remove the pedestal stand from the TV by sliding the pedestal stand away from the TV.

Sep 28, 2009 | Toshiba REGZA 32WLG66 32 in. Television

3 Answers

I need an Insignia TV stand for a 42" LCD HDTV


Try the T.V. manufactures website, E-Bay or the store where you got the T.V. from.

Jul 15, 2009 | Insignia LCDTV26 26 in. Television

1 Answer

Need base for Insignia TV


It will either slide out from the front/back or to the side..Some actually bolt on from the bottom using screws/bolts.And then again some are not meant to be taken off.Make sure it is a wall mountable tv.Then try to take the stand off as directed.

May 29, 2009 | Insignia LCDTV26 26 in. Television

1 Answer

Insignia TV stand screws


Had same problem with Insignia TV...#12 - 24 x 1/2" machine screws...found at Home Depot in bagged items (can't use longer because some of the holes don't go all the way thru)

May 20, 2009 | Insignia LCDTV26 26 in. Television

1 Answer

Cannot figure out how to remove stand so I can mount TV on wall


did you figure this out? I only ask because I need the stand for my TV. Could you sell me yours?

Thanks

Anthony
amsaxo@yahoo.com


Dec 02, 2008 | Sylvania 6620LDG 20 in. EDTV-Ready LCD...

2 Answers

Tv stand screws


Check the kitchen drawer next to the fridge for the screws !!

When you get new screws, use lengths 1/2".. any longer and you might hit something inside.

Don't know why this is posted under IS-LCDTV26.. I would pull a screw from my 26" and measure it, but it's most likely different than your 42"

Sep 01, 2008 | Insignia LCDTV26 26 in. Television

1 Answer

Is this TV wall mountable?


Just mounted this TV this past weekend...Used Peerless flat panel wall mount bought on Ebay for $39.99 free shipping...Remove the stand by removing the 4 small screws on the back of the tv where the stand connects...then slide the stand off from the bottom...VOILA

Jul 22, 2008 | Sylvania LC320SS8 32 in. LCD Television

1 Answer

Remove base of Insignia ns-ltdvd26-09 lcd tv for wall mounting


Open up the panel on the back of the TV which covers the various input connections. At the bottom of the area previously covered, there are 8 screws (two rows of four screws). Remove them, and the entire stand should now slide right out of the TV. You can then replace the screws back in their holes, so you don't lose them. You do not need to disassemble the stand to do this.

Jul 11, 2008 | Flat Panel Televisions

6 Answers

Remove base of Insignia ns-ltdvd26-09


to remove base from insignia tv
1)remove plastic cover from bottom rear of tv
2)remove 8 philips head screws on rear of tv above base
3)pick up tv and base will come off

once you remove it you realize how easy it is

Jun 29, 2008 | Insignia LCDTV26 26 in. Television

4 Answers

Akai 32"


I just purchased this unit and briefly looked at removing the stand though I haven't taken it off yet. Anyways, I think you need to remove the black metal mounting frame from the TV before trying to unscrew the stand (4 screws) from the metal frame. After the frame is off the TV, I think you can then get at a couple of hidden screws to remove the stand from frame. I don't know if the frame goes back on the TV or not.

Dec 01, 2007 | Akai LCT3201AD 32 in. LCD Television

Not finding what you are looking for?
Insignia LCDTV26 26 in. Television Logo

714 people viewed this question

Ask a Question

Usually answered in minutes!

Top Insignia Flat Panel Televisions Experts

Sp Gupta

Level 3 Expert

667 Answers

Gareth Cockram
Gareth Cockram

Level 3 Expert

657 Answers

The Wyzzyrd

Level 2 Expert

83 Answers

Are you an Insignia Flat Panel Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...