Question about Janome Memory Craft 9000 Computerized Sewing Machine

1 Answer

My janome 11000 memorycraft's needle threader has jammed in the down position and cannot be moved

My needle threader has jammed down in my Janome memorycraft 11000 and I can't move it. What should I do? I have only had this machine for one month and it is a new machine'

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Thanks to floraq803, we have our 11000 working again. The needle threader was stuck in the down position. We turned off the machine, and turned the wheel (which controls where the needle is) until the needle threader bar was straight (approximately 1/2 way between the needle being all the way down and all the way up). Turned on the machine and the threader came back up again. Now back to sewing.

Posted on Jan 15, 2014

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Janome 9000 seems to be jammed.

I had the same problem with my 9000. After my third visit to the repair shop they finally told me to always check my thread uptake lever. I have had no problems since.

Posted on Jan 10, 2010

  • 1 Answer

SOURCE: Janome Memory Craft 7000 Sewing

My Memory Craft 7000 sometimes does the same thing, if it's very cold. Try warming it up by placing it near a heat source, a vent or a floor heater, for a few minutes. Then it works perfectly.
I've used these machines for over 20 years now, and they're my favorite!

If this doesn't solve your problem, you need to take it in for servicing.

They are work horses, but they do need their maintenance from time to time.

I hope this helps you.

Posted on Jan 18, 2009

  • 11 Answers

SOURCE: janome mylock 634D overlocker

this very same thing happened to my flat machine turned out to be a piec of material jammed in the workings also wrong oil used or it might be thread jammed try and see

Posted on Jun 16, 2009

  • 1 Answer

SOURCE: Janome MC 10001 auto. needle threader stuck in up position.

I have a Janome 10001 and the needle threader is stuck in the down position and I cannot get it up. Help, please !!!!

Posted on Jan 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The needle threader on my Janome 6260 quit working. The needle is inserted correctly.


Is the threader broken or just not meeting the needle eye? If broken, it can most likely be repaired.

If the threader is not meeting the needle eye, adjust the needle height so the threader meets the eye and intercept the thread. I have a 60's machine with a threader that needs the needle height manually adjusted because the needle does not stop in any particular place. Usually, if I raise the needle to its highest, the threader will work.

...

Oct 06, 2016 | Janome Sewing Machines

1 Answer

Hand wheel won't move.Scissorbutton wont work.


Repairing a Janome or New Home Sewing Machine ...

www.thriftyfun.com/Repairing-a-Janome-or-New-Home-Sewing-Machin...
Question: Memory Craft Machine Won't Run ... I'm a computer repair technician and good with tools, is this something I could fix or should we .... machine which will zig zag fine if i turn the wheel by hand or sew very slowly; as soon as I speed ...

Janome won t turn Sewing Machines Questions & Answers ...

www.fixya.com > Forum > Tags > won t turn > Sewing Machines
Janome sewing machines won t turn related questions and answers. ... Ad. Question about Memorycraft 6500P Computerized Sewing Machine ... it could be a part has worn or broken, esecially when the hand wheel won't turn,, it needs to be.

Janome wheel not turning Sewing Machines Questions ...

www.fixya.com > Forum > Tags > wheel not turning > Sewing Machines
Janome sewing machines wheel not turning related questions and answers. ... 10000 janome jamming fly wheel won't turn fly wheel won't turn warning for too thick ...the hand wheel is not moving the needle at all Hi I was unable to move the needle at all ... Janome Memory Craft 9000 Computerized Sewing Machine.

Jan 25, 2016 | Janome Memorycraft 6500P Computerized...

1 Answer

Automatic needle threader stuck


You may have a thread stuck in your bobbin area. Remove your bobbin, brush gently with a clean soft brush to remove dust and/or thread bits, then gently wiggle your hand wheel back and forth, and brush again. This should free up your machine.

Jul 09, 2014 | Janome Sewist 500 Sewing Machine

1 Answer

Needle stuck in clamp


it souds like the needle clamp needs to be checked, to see why
the needles are jammed in the needle clamp. it may need to be
replaced, a sewing machine shop can tell you for sure what's wrong

May 31, 2012 | Janome Sewing Machines

1 Answer

I can't get the needle to thread automatically on my new Janome 3160.


if the needle threader is not working, try rethreading the machine & if that
doesn't help then take the machine back to the place you bought it & see what they will do about it

May 02, 2012 | Sewing Machines

1 Answer

Janome 1860 needle threader


If the hook is bent, you might be able to straighten it, but I would go to my dealer and purchase a new threader. It is much easier to replace it.

Feb 06, 2012 | Janome Sewing Machines

1 Answer

Janome 6500 jamming - cleaned out bobbin case - no help


Have you removed the bobbin holder and then put it back in lining up the little red markings on the right hand side? If the case has moved slightly then it will keep jamming and the bobbin thread won't clear to form a stitch. The case is held in place by a magnet and a stopper but it will dislodge if you have a bad thread jam, then it keeps happening even if you have removed all the thread because its not in position.

Check this solution for image how to remove and replace the bobbin case. http://www.fixya.com/support/t9289728-bobbin_seems

When you take out the bobbin case, carefully inspect it for any damage and burrs in the black plastic, if there are any then file them carefully out with a nail file or fine sandpaper, a burr will keep catching thread too. Or you may actually need to replace the bobbin holder if it has been pierced by the needle badly, they are about $35 or so.

You may also want to get it serviced. On my 6500 during its last service the technician added a little piece that is a Janome "after sale replacement" part. It is slightly longer than the standard part, and is a little metal bit on the left hand side of the rotary hook area which is holding the bobbin holder in place better. Haven't had a major jam up since this was fitted so you may want to get this fitted on yours too.

Jul 19, 2011 | Janome Memorycraft 6500P Computerized...

2 Answers

Janome MC 10001 auto. needle threader stuck in up position.


You are threading the top of the machine incorrectly.

Make sure the needle is in correctly with the flat side to the rear of the machine, make sure to thread the upper and lower portions of the machine correctly. If this does not solve your problem, please respond.

Feb 12, 2009 | Janome Memory Craft 9000 Computerized...

Not finding what you are looking for?
Janome Memory Craft 9000 Computerized Sewing Machine Logo

259 people viewed this question

Ask a Question

Usually answered in minutes!

Top Janome Sewing Machines Experts

Tally Girl
Tally Girl

Level 3 Expert

1122 Answers

Douglas Plant
Douglas Plant

Level 2 Expert

184 Answers

Irene Tulloch

Level 2 Expert

458 Answers

Are you a Janome Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...