Question about Panasonic SC-HT520 System

1 Answer

Cannot operate SA-HT520 by remote control

The DVD player is not receiving the signal from the remote - I have tried the remote on another player and it works so I have ascertained that the player is the problem (not the remote). There are only limited buttoms on the player itself for operation.

Posted by on

  • digitaldecks May 05, 2009

    same issue. remote does nothing to the main box. yet when tried on my other panny system all ok. is there like a hard reset or something maybe


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer


Posted on Jun 11, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Dvd player working remote not changed batteries

Turn your phone camera on and press a button on the DVD remote. If the remote is working you should be able to see the transmitting light on the remote flashing as you look at it on your camera screen. If it doesn't flash there is something wrong with the remote. If it flashes then the fault may lie with the DVD receiving the signal.

Feb 23, 2016 | Televison & Video

1 Answer

Remote control does not work

A few things may help before you invest in a new remote. One, open remote and make sure no dust is inside and the batteries are good. Use compressed air to blow out the remote. Next, try cleaning the little electric eye at the top of the remote with rubbing alcohol. Just a little hit to clean the eye. Also find the spot on the player that receives the signal from the remote and make sure it is clean and not blocking any signal. If all of that fails, you may need a new remote.

Dec 07, 2013 | Televison & Video

1 Answer

Status on recorder says load and I cant move it off there

I would take the other route: The remote can be tested without the unit--all shops(ours does) have a tester--point the remote and press any or all buttons and the tester reacts if the remote is sending a signal.

Some digital cameras will react in the same way on their display screens in a dark room with a flash.

check the remote first.

Jun 14, 2012 | Philips DVDR3440H DVD Recorder/HDD...

1 Answer

Dish network remote to run RCA DVD player

I had rca remote that did not recieve ir signals but rf signals instead. Check online with rca or in owners manual for what type of signal factory remote sends. The dvd player I had was 5 dvd and that was the case. Dish might have an option like direct tv where you can program rf signals as well. Call dish network support or look online

Apr 25, 2010 | DISH Network IR Remote Control

1 Answer

LG RHT 387H Will not respond to remote commandsI have changed the remote battery but still does not work this was purchased on 30/01/2009 Not a long time to last, but just outside any guarantee

It is bad that you don't have a guarantee running now. Its just 15 months. So just see if your player is accepting commands from the switches of the dvd player itself.If no, it is the problem of your player. If your player do respond to these switches, try another remote of the same player on your player. If that too doesn't works, Your signal receiver of the player is faulty, get it replaced. If the other remote works, the problem is with your remote. You might have dropped it down or something like that. Get your remote checked by an expert nearby.

Apr 13, 2010 | Televison & Video

1 Answer

My remote for MWD2205 dvd/vcr player won't do anything except open and close dvd door. I bought it used and it didn't come with instructions.

Hi dear,
Please use the remote very close to the dvd so that the dvd player can receive the signal properly. This can happen with low quality dvd players. If the problem persists, then consult to a dvd player mechanics to replace your remote.


Jun 08, 2009 | Philips MWD2205 DVD Player/VCR

1 Answer

Receiver doesn't respond on remote signals

Low batteries can cause a symptom like this. Have you tried to replace them yet?...accordianman

Oct 04, 2007 | Onkyo TX-DS595 Receiver

2 Answers

Dvd remote stopped working

open up your remote then separate the rubber / key pads then clean the cercuit using home dry cleaner and leave to dry close your remote gently and its fresh again. reason for this is practice is because moist cause cover between pads and circuit board and thus no contact then no function

Jul 18, 2007 | KLH DVD8350 DVD Player

Not finding what you are looking for?
Panasonic SC-HT520 System Logo

Related Topics:

903 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Audio Players & Recorders Experts


Level 3 Expert

4946 Answers


Level 3 Expert

102366 Answers

Michael Kovalik III
Michael Kovalik III

Level 2 Expert

117 Answers

Are you a Panasonic Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides