Tricity Bendix AW1000W Front Load Washer Logo
Allan Bell-Brown
Allan Bell-Brown Posted on Jan 26, 2009
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Manual spin When I put the Machine dial to spin the clothes, at the end of the cycle they are coming out wet. When I do this manually the programs are not functioning correctly when set for another wash.

Answer This Question
  • andrewfodor Feb 13, 2009

    Hi I have the same problem. HAve tried many times going through the programmes and also going straight to 6 - spin. The drum appears to try and spin up to speed but then gives up. I'm assuming that there is a drum speed sensor somewhere which may be faulty. Any assistance would be grateful..Clothes should not be coming out wringing wet after s 1000 spin cycle!!!!

×

1 Answer

Anonymous

Level 2:

An expert who has achieved level 2 by getting 100 points
MVP:

An expert that got 5 achievements.
Governor:

An expert whose answer got voted for 20 times.
Hot-Shot:

An expert who has answered 20 questions.

  • Expert 130 Answers
  • Posted on Jan 26, 2009
Anonymous
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points
MVP:

An expert that got 5 achievements.
Governor:

An expert whose answer got voted for 20 times.
Hot-Shot:

An expert who has answered 20 questions.

Joined: Jan 24, 2009
Answers
130
Questions
2
Helped
50591
Points
289

This may sound crazy. If your machine looks to be spinning out and draining fine it may be you (NO DISRESPECT INTENDED). I see this alot. Try cutting back to about a tablespoon of "HE' soap. Before doing this run some vinegar thru the wash cycle to clean out the machine.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Kenmore Series 70 Top Load Washer Direct Drive Model # 110.20722991 Serial# CL 1134809 Wet Clothes after Spin Cycle
many machine spin a full tub as they are pumping the water out
this helps to even out the washing load and reduce the unbalance situation
when the water is removed , the machine progresses the program to a high speed spin
call a technician as there may be a problem in the program board
Read full answer
Jun 11, 2016 • Kenmore Washing Machines
0helpful
1answer

Clothes come out of washer wet
Most often you have a worn out belt that spins the drum when it is time to spin dry. Upend the machine and check the belt, if it has one.
A new drive belt should fix you right up.
Read full answer
Mar 14, 2016 • Washing Machines
0helpful
2answers

Why is my whirlpool auto load sensing washing machine spraying water while in final spinning cycle?
you could have a bad temperture sensor bad are water valve but first check an make sure the washer drain alway check your drain hose for clog are lint are trash in pump an last you could have a bad timer if you dont know how to check these call a applince service for repair ok
Read full answer
Dec 13, 2017 • Washing Machines
0helpful
1answer

My machine is spinning, but clothes are still very wet, have to drain and spin at least twice to get them dry enough to put in the dryer
If the washer doesn't reach its proper spin speed, the clothes may be too wet at the end of a cycle. Check to be sure the load is properly balanced and run a spin cycle again. If the clothes are still wet, you may have a worn or loose belt (Maytag®), a worn clutch (GE®/Hotpoint®), or a worn motor pulley or tub bearing. Replace the applicable component.
Read full answer
Feb 08, 2011 • GE Washing Machines
0helpful
1answer

Washing machine 11 years old is jumping on the wash cycles. EG instead of taking 25 mins its taking 10 mins to complete -clothes coming out wet unless manually turn to spin again
It is possible that the program is not running to the designed settings and so the program seems to skip the cycle.
The clothes come out wet because the spin cycle is not activated in the set program. Hence the program controller needs a check.
Read full answer
Jan 17, 2011 • Hoover Washing Machines
0helpful
1answer

Clothes are soaking wet at end of full cycle , it
clean your filter
Read full answer
Jun 29, 2010 • Whirlpool Ultimate Care II LSQ9564J Top...
2helpful
1answer

Clothes are to wet after spin cycle
The clothes are wet after spinning When the clothes are wet at the end of a cycle, check these: Motor coupler Spin cycle Siphoning Water-inlet valve Motor coupler To test the motor coupler, re-start the washer in its spin cycle. Let the machine run for a minute, and then open the lid and notice whether the tub is spinning: If it's spinning when you lift the lid, the coupler is fine. If it isn't spinning--and your machine was produced by Whirlpool®--you may have a broken coupler. Many Whirlpool-made washers use a small, relatively inexpensive device called a motor coupling. This plastic-and-rubber component is mounted to the shaft of the motor on one side, and to the transmission on the other. Over time, the coupler wears out and fails. When that happens, you need to replace it completely. Spin cycle If the washer doesn't reach its proper spin speed, the clothes may be too wet at the end of a cycle. Check to be sure the load is properly balanced and run a spin cycle again. If the clothes are still wet, you may have a worn or loose belt (Maytag®), a worn clutch (GE®/Hotpoint®), or a worn motor pulley or tub bearing. Replace the applicable component. Alternatively, there could be clothes caught between the inner and outer tubs. Read the "It spins but won't pump" section of the "It won't drain" section. Also, there could be other things that cause friction on the drive train. Seek the assistance of a qualified appliance repair technician. Siphoning If the water that pumps from the machine goes right back into the machine after the spin cycle, it may be because your washer is siphoning the water from a laundry tub with a slow drain, back into the washer. Try to improve the draining of the laundry tub. (Is there something stuck in the drain?) Also, be sure the drain hose doesn't reach more than about 4 inches into the laundry tub. If it does, cut off the excess. Water-inlet valve Water-inlet valves eventually fail. One problem that may develop with a water-inlet valve is that it can no longer completely shut off when the electricity is turned off to it. Then, the valve may leak and drip water into the clothes tub--you may notice that your washer has water in it when you haven't used it for a few days. To fix this, replace the valve.
Read full answer
Jan 24, 2010 • Kenmore Washing Machines
4helpful
1answer

My clothe come out very wet at the end of the wash cycle
If the pump is clogged and can't release all the water it won't go into final high spin. Remove lower cover and locate coin catch and unscrew it. Water will come out, so be ready. If it's full of stuff, this is probably the problem.
Read full answer
Mar 13, 2009 • Kenmore HE2 Plus Front Load Washer
3helpful
1answer

Wet clothes at end of spin cycle
sounds like your transmission is not working properly. check your warranty information. (should be in your owners manual) many of the whirlpool made top loaders came with a 5 year warranty on the transmission/gear case
Read full answer
Dec 29, 2008 • Kenmore 22422 Top Load Washer
7helpful
4answers

Bosch Nexxt 800 washer won't drain clothes fully
There is not a Spin Only Cycle BUT there is a REFRESH cycle that will take about 10 minutes.

Sometimes when the load is unbalanced and the machine can not balance the load by itself, the clothes will remain soaked. To avoid this, make sure you always have a balance of small and large things and when loading your machine, do not shove the items in so they ball up.


Read full answer
Dec 27, 2008 • Bosch 3.81 cu ft WFMC530 1UC Nexxt 500...
Not finding what you are looking for?

View Most Popular

AW1000W Front Load Washer

  • Washing Machines

Related Question

Kenmore Series 70 Top Load Washer Direct Drive Model # 110.20722991 Serial# CL 1134809 Wet Clothes after Spin Cycle

  • Kenmore Washing Machines

Related Topics

219 views

Ask a Question

Usually answered in minutes!

Popular Questions

WDB1043M Bendix Washer/Dryer

Tricity Bendix WDR1040W Front Load...

My tricity bendix washing machine flashing and beeping end light

Tricity Bendix AW1400W Front Load...

Bendix washer-dryer door won't open

Tricity Bendix WDR1040W Front Load...

Light Blinking (start/pause)

Tricity Bendix AW1000W Front Load...

My machine won't take the fabric conditioner. It

Tricity Bendix AW1000W Front Load...

Top Tricity Bendix Washing Machines Experts

Paul Bade

Level 3 Expert

1818 Answers

Brad Brown

Level 3 Expert

19187 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

66931 Answers

Are you a Tricity Bendix Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
. AW1000W Front Load Washer Manual

AW1000W Front Load...

Loading...