Question about Transceivers

1 Answer

Transmiter Crossing allocated band - Transceivers

Posted by on

  • Louie  Role
    Louie Role May 11, 2010

    Hi and welcome to FixYa,

    Almost always, your described condition could be caused by some possibilities (among others):


    • over modulation;

    • spurious transmissions (splatter);

    • harmonics.
    Pls pst back what band you are having issues and with what equipment.

    Good luck and thank you for using FixYa.


×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 6,966 Answers

Were you able to view my clarification request?

Posted on Feb 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a KENWOOD TS-940SAT HF Transceiver that powers up with the TX indicator on, no power output and no receive.


Very little information about the situation of the transceiver is provided, it might be a complex one. The Kenwood TS-940SAT features a built-in automatic antenna tuner covers the amateur bands 160 through 10 meters. It is advisable for you to reinstall the transceiver and follow the right set up step to see if it works out eventually.

Apr 18, 2016 | Transceivers

2 Answers

Transceiver signal interference


The FT-840 uses a die-cast RF power amp with thermally switched fan to ensure full power output (up to 100 watts). The digitally synthesized local signals ensure clean, low-noise transmitter output on all HF amateur band. There might be no AC line interference. it has strong Rf output. any AC line intersect does not affect its radio performance. Check and adjust RF power so to maintain proper output. some times more RF power generated at the output may cause interference. adjust Rf power..Even some unfiltered Noise getting the other end of the end may calso cause interference. Check for any Ripple voltages present at the output. Contact authorised service station for further Rectification. thank you shanth

Dec 23, 2007 | Transceivers

1 Answer

Operating or tech manual/or/ switch functions


well I also lost the little tag plate.
Left indeed is a keyborad lock.
On my FTC-1903 the middel and right toggle switch does not seem to have any effect.

The middel one switches between "busy - manual - ...?..." and the right one between "USA-International". I guess the right one switches to a preset order of channel allocation, different for USA or other countries.

On mine swicthing middel or roght switch does not seem to give any effect.
So I would like to open up the set but would like to do so with the help of a schematic drawing.

Any source to find that?

jan
ON3ZTT

May 09, 2009 | Transceivers

1 Answer

Ssb


what about ssb, you mean what does it mean
(single side band)

Jan 21, 2009 | Transceivers

1 Answer

Problem with a Kenwood TS 2000 Amateur Radio Transceiver


73s I have heard of similar problems and some were heating related. the best is to check if your rig is heating up causing it to switch off and lose memory when switched back on. I have a buddy who had an unusual experience where he actually dropped frequencies so low that he could pick up ordinary radio frequency and also go into bands like 27mhz and 25mhz. But once switched off, the rig worked normal again. If you are experiencing heat problems then i suggest you put in a fan and remove all dust from inside the rig. You could probably also be having problems with power supply either internal or external. If all else fails, refer to a good repair shop this type of radios are very sensitive.

Oct 01, 2008 | Transceivers

4 Answers

TS 2000 KENWOOD TRANCEIVER


I have the same problem with my TS2000 , in VHF I can heard small signals only if I turn on the PRE Amplifier ...
It start just few hours of use .

Jul 31, 2008 | Transceivers

2 Answers

How do I make it work


It depends on the channels on the walkie talkies.

Can you supply the frz range of the TRC, and walkie talkies make and model and I will try and get the frez on the channels for you.

I can then tell if it will work or not.

Apr 27, 2008 | Transceivers

Not finding what you are looking for?
Transceivers Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Transceivers Experts

scramblepad
scramblepad

Level 2 Expert

66 Answers

brian soufane

Level 3 Expert

693 Answers

yadayada
yadayada

Level 3 Expert

60960 Answers

Are you a Transceiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...