Question about Kenmore 24 in. 16352 / 16354 / 16359 Built-in Dishwasher

2 Answers

Kenmore elite dishwasher stopped in middle of cycle with water still inside. Checked breaker. Replace the hole control panel, door latch from a used kenmore elite. Work for half a cycle and quit with water still inside just like the first time.

Posted by on

  • 2 more comments 
  • brdixson Jan 27, 2009

    ???? There is no error message. Its like theirs know power, but their is. the control panel doesn't light up at all.

  • bethbailie Mar 27, 2009

    Same deal. New dishwasher...Cycle stopped, water inside, no lights or sound. Bad control panel? Chronic issue?

  • Anonymous May 24, 2009

    Kenmore ultra dishwasher stopped in middle of cycle with water still inside. Checked breaker. Replace the hole control panel, door latch from a used kenmore elite. Work for half a cycle and quit with water still inside just like the first time.

  • Anonymous Mar 16, 2014

    water leaking from bottom of dishwasher

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Contributor
  • 79 Answers

Here's your solution (free PDF) - Kenmore Elite Dishwasher Manual

Posted on Feb 28, 2013

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My Smeg (never buying brand again) dishwasher UKSTX1 has error message e9 not covered in manual

Posted on Jan 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Should the inside of the elite dishwasher still be wet at the end of the cycle?


Martha,
If you are talking about having a small amount of water down in the bottom of your dishwasher, that is normal. There is a sump down there that needs to have water in it. If you are talking about having water on the walls, that is probably just condensation from the cycle when you run the heater. Try cracking the door after the cycle is done to let the excess steam out of the dishwasher and that may eliminate the water on the walls. Hope this helps!

Apr 03, 2015 | Kenmore Dishwashers

1 Answer

Kenmore elite dishwasher stops in mid cycle green clean light flashes 8 times pauses and then flashes one more time


Float Switch

The float switch may be hung up and this can cause the dishwasher to be stuck in a cycle. see the diagram

Timer / Control

If your dishwasher gets stuck in a cycle first try shutting off the breaker for at least 5 minutes if this does not correct the problem you will need to replace timer/electronic control.

God bless you725787ea-1dc1-4b47-8830-53525552db22.gif

May 23, 2013 | Kenmore Dishwashers

1 Answer

My kenmore Elite stopped working after my daughter open the door during a cycle. There seems to be no power. Circuit breaker is fine. Any thoughts? Thanks


Check the wall socket for power. Sometimes the power cord disconnects at the dishwasher (inside the junction box, behind the bottom kick panel), if this is the case, the wiring must be repaired or replaced.

Mar 28, 2010 | Kenmore 24 in. 17482 / 17484 / 17489...

1 Answer

Dishwasher won't start until running until at


The 2 minutes is most likely the "Fill" time in the cycle therefore since the water supply is active the fill solenoid is spent or not getting a signal.

Dec 12, 2009 | Kenmore Dishwashers

1 Answer

Trouble shooting kenmore dishwasher


I have a kenmore ultra wash II Model #1675590 Serial # FC1024731

Will not run and water is standing in the bottom. I have checked the electrical breaker and tried different cycles. Can you help.

Oct 03, 2008 | Kenmore 18 in. 14432 / 14439 Built-in...

1 Answer

Kenmore 16604


No reset button. Most likely, the thermal fuse went out. This happens if the water inside gets too hot. The thermal fuse is clipped to the electronic board behind the console. The heater thermostat is underneath the tub on the right side. The parts should cost about $25.00 total.
OR: the connection inside the connection box melted itself apart (installation error.) This happens, but not very often. Turn off the breaker. Remove the toe panel and the cover over the terminal box. Physically inspect the connections. You'll know immediately if this is the problem.

Good luck!

Mar 31, 2008 | Kenmore 16602 / 16604 / 16609 Built-in...

22 Answers

Kenmore elite dishwasher


press back and forth between hi-tempwash and sani rinse several times to get all lights to come on if not then press sani rinse and heated dry back and forth several times. one of though combos will start the test mode. the test mode will stop the light from blinking and you can use the dishwasher again

Nov 27, 2007 | Kenmore 24 in. 17482 / 17484 / 17489...

Not finding what you are looking for?
Kenmore 24 in. 16352 / 16354 / 16359 Built-in Dishwasher Logo

2,683 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dishwashers Experts

Fred Sops

Level 2 Expert

271 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Raisin Brann

Level 1 Expert

28 Answers

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...