Question about Washing Machines

Open Question

What are the specs on the whirlpool W10140920 B washer and W10136491 A?

I can't find the specs for this washer & dryer pair anywhere online and I'm trying to sell them

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

falspet
  • 438 Answers

SOURCE: whirlpool stacked washer/dryer won't heat

Check your wiring connections, then check your upper limit thermostat for continuity with an ohm meter this unit should show short when cold, open when to hot. It will be located near the heating coil assembly.

Posted on Apr 16, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I start dryer without Knob 123c7931-2?


All you need to do is use a small pair of pliers to turn the shaft that the knob slids onto. Its best to go to a parts place that sells new and used partsand get a knob that works.

Jul 14, 2014 | GE Washing Machines

1 Answer

Can I separate the pair and just use the dryer?


I wouldn't know as you are asking this question in vacuum section

Jan 26, 2014 | Whirlpool LTE5243D Top Load Stacked...

1 Answer

Washer won't drain or enter spin cycle


SHOULD BE THE LID SWITCH... THERE IS TWO SWITCHS INSIDE, ONE THAT STOP THE MACHINE, AND ONE TO LOCK THE DOOR. YOU SHOULD SEE THERE IS TWO PAIRS OF WIRES THAT CONECT WITH THE LID SWITCH, ONE PAIR IN THE FRONT, AND ANOTHER PAIR IN THE RIGHT SIDE, THAT RIGHT SIDE IS THE PROBLEM, INSIDE THE LID SWITCH MUST BE BROKEN. TRY TO MOVE THE PLATED LOCKING PIN IN THE DIRECTION THAT LOCKS THE DOOR, AND IT MIGHT DRAIN AND SPIN. IF THAT THE PROBLEM, YOU SHOULD GET A NEW SWITCH (MODEL 134101800), AND YOURE DONE.
GOOD LUCK
MARIO

May 07, 2013 | GE Spacemaker Washer and Dryer Electric...

1 Answer

Broken bumper on a whirlpool Model # LEC7848DQO


the part number is 238614 the pic below is the part that you need


3_4_2013_3_15_03_pm.jpg

okay

Feb 15, 2013 | Whirlpool Clothes Dryer Lid Bumper 17258

1 Answer

Whirlpool W10140920 agitates with no water in the tub


I've had the same problem..3 times in 2 years.
EVERY time I needed to relpace the switch sensor (behind the water temp knob.) It fixes the problem, but continues to happen. I am going to get a new NON Whirlpool washer today.

Feb 12, 2013 | Kenmore Washing Machines

1 Answer

Any particular problems with installing whirlpool stacker washer/dryer in RV


the main problem is how stable the foundation is for the laundry center when it goes into its spin cycle.

Sep 11, 2012 | Whirlpool LTE5243D Top Load Stacked...

1 Answer

I have a Frigidaire Stacker washer dryer that has no model number anywhere and a tub seal with numbers that I have been unable to cross reference.


John, check out http://www.easyapplianceparts.com/ModelFrames.aspx?ModelID=1084015&ModelNum=FEX831CS0&mfgModelNum=&ManufactureID=4&Selected=OMQBC08N&Position=5&mfg=Frigidaire&Type=&Mark=5r

Jun 02, 2012 | Frigidaire FEX831CS Top Load Stacked...

1 Answer

I just purchased a washer and dryer pair made by kenmore...they both came out of a storage unit and the guy promised me they both worked...i purchased them for my daughter who is getting married in...


The best for you is to contact KENMORE support section online or phone in your city and tell them your problem. Since you have recently purchased the machine, it is under warranty period. So they have to replace it or repair it free of cost. Also inform the local dealer from whom you purchased the machine. Keep the pressure on.

Aug 15, 2011 | Washing Machines

1 Answer

How to shut off dryer end of cycle beep. Can u run


If the model number is correct, the dryer End of Cycle signal cannot be adjusted or turned off. The informatrion is listed on page 11 of the Owner's Manual:

http://www.managemylife.com/mmh/owner_manuals/16695/WHIRLPOOL-Laundry-Centers-L0710382?brand_name_search=LTE5243D

The only way to turn the signal off, is to remove the operator console, locate the signal (buzzer) module and disconnect the wire(s). The buzzer is listed as item 32 under the "Washer/Dryer Control Panel" parts listing:

http://www.searspartsdirect.com/partsdirect/part-model/Whirlpool-Parts/Washer-dryer-combo-Parts/Model-YLTE5243DQ2/1198/0152000/W0702346/00001?blt=06&prst=&shdMod=

CAUTION: If you choose this option, make sure you UNPLUG the washer/dryer before servicing anything inside. If you disconnect any wires, make sure you cover them with heat shrink or electrical tape to keep them from coming into contact with anything else.

The washer and dryer use a common power source, but the rest of the functions operate independently of each other. You can safely run both units at the same time.

If need further assistance, please let me know. I hope this helps you.

Aug 09, 2011 | Whirlpool LTE5243D Top Load Stacked...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

773 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1460 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Brad Brown

Level 3 Expert

15557 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...