Question about Garden

1 Answer

Need schematics for a stihl MS201T chainsaw - Garden

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,807 Answers

Like rocking horse poo at the moment, none available for free online as yet.contact your stihl dealer for a paper version.

Posted on Jan 19, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: STIHL CHAINSAW MIXTURE SETTINGS

one turn high and low 66 has compesator carby willrun rich up high but will lean under load

Posted on Sep 03, 2008

  • 2692 Answers

SOURCE: 0340 AV stihl chainsaw won't fire

Spray a little starter fluid down the carburator . It is starts then is is a fuel problem. Most likely a gummed up carburator. Remove and clean . 

Posted on Jan 24, 2009

Dolfoff
  • 148 Answers

SOURCE: tunning specification for a stihl 028 chainsaw?

I'm not sure there are any "endorsed" tuning specs from Stihl as weather, temperature, fuel quality etc all contribute to engine performance.
Pictures of all types are all over the web.

As for the carb tuning procedure, maybe I can help?

Start with fresh fuel, all filters clean, and bar and chain installed. Also, fill the chain oil tank with bar/chain oil and VERIFY that the chain oiler works properly.
Initial fuel mixture settings (the H and L screws) should be 1.5 - 2 complete revolutions counter clockwise from lightly seated. Sight the carb's throttle plate and adjust idle screw counter clockwise until the plate stops moving.(Throttle closed completely.) Then go back clockwise 3 complete revolutions. This will produce an acceptable startup condition on a HEALTHY saw.
Clamp the bar in a STURDY bench vise and roll the chain with the shank of a screwdriver to verify it is clear. BE SAFE!
Choke the saw and pull the starter rope until the engine "burps".
NOTE: If no burp after 6 pulls, stop! Something is wrong.
After the burp, set choke to half and pull starter until it runs. The settings I gave should produce a slightly rich condition and a slightly high idle. (Chain will be in motion!)

Blip the throttle trigger and idle it down just enough to keep it running during the tune procedure.
Step 1) Using the "L" screw (closest to the engine), turn it clockwise until the engine smooths out or possibly increases RPM. Back it out slightly until the engine has a slight "LOPE" sound to it. (Like a drag car on nitro).
Step 2) Accelerate the engine to full throttle and go to the "H" screw (closest to the air filter) and slowly turn it clockwise and note the RPM increase. There will come a point when the saw will "Top-Out" and loose power. Not even enough power to turn an maintain empty chain's RPM! Go back counter clockwise to the edge of that point, and counter clockwise another fourth (1/4) revolution.
Step 3) Idle the saw back down. Again go to the "L" screw and repeat Step 1.
Step 4) Repeat Step 2.
Step 5) Idle the saw down until the chain stops moving completely. NOTE: Don't settle for a "crawling chain" condition. If the steps above are performed well and all else is healthy, you should be able to idle the engine down to a ridiculously low RPM and it will not shut off.

Hope this helps,
Dolf-

Posted on Oct 13, 2009

SOURCE: stihl 009 chainsaw

http://www.ultimatehandyman.co.uk/manuals/stihl/19.pdf
manual above it is all in there..

Posted on Mar 26, 2010

  • 1 Answer

SOURCE: how to find date of manufacture for stihl chainsaw

call up Stihl USA and ask them when your saw was manufactured. Tell them you bought it used and give them the serial. They told me!

Posted on May 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I obtain a copy of the stihl schematics for the Stihl arborsaw 015


Stihl, like most makes, is online. Go to Stihl site and search for your model.

Aug 18, 2014 | Garden

1 Answer

Stihl schematics


i can help but need to know which model you're after.?

Jul 29, 2014 | Stihl POLE SAW GAS CHAINSA

1 Answer

Stihl schematics


Go to Stihl site and search for your model

Jul 27, 2014 | Stihl POLE SAW GAS CHAINSA

1 Answer

I need schematics for an ms201t


None available online as yet.

Jan 19, 2013 | Garden

1 Answer

Schematics sthil ms192


Only trained STIHL technicians and STIHL dealers have those. What part do you need specifically, I have the breakdown you need and will look up the parts for you.

Mar 25, 2012 | Stihl Garden

1 Answer

Stihl ms 250 diagrams


All manuals available at www.stihlusa.com

Mar 01, 2012 | Stihl Garden

Not finding what you are looking for?
Garden Logo

Related Topics:

231 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2475 Answers

john h

Level 3 Expert

11064 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...