- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
It sounds like you're not in the right input source (mode) or you have a external source selected. I show your unit as a 1995 model and so check your Tape 1, Tape 2 selection buttons. These "Tape" selection button get dirty contacts that will kill the audio. To clean, with the volume low, press them on and off around 20 times each. This works the contacts back-n-forth and will help clean them.
The ViviCam 5022 is designed primarily as a still camera, with some video capabilities grafted on. It does not record sound. You can add a soundtrack using video-editing software on a computer, but you cannot record one on the camera.
That probably wasn't the answer you wanted to see, but there it is.
First, turn the volume most of the way down so you don't blow something out. Set it to about 20%, if there is a readout.
Then, look for a speaker switch. You didn't provide the make or model of your receiver, so it is very difficult to provide specific information, but most receivers have a switch which enables the speakers. Make sure that is turned on.
Next, look for a "tape monitor" button or switch. This is the most likely cause of the problem. Press that button or switch, and look on the receiver's display panel to see if you see a "tape monitor" light go on or off.
There may also be a "video monitor" button or switch. Repeat the above directions for that.
make sure when you take a video you adjust the volume first so then you will have the sound you want..press the mode button to access in audio mode with the arrow buttons then press ok button. in the audio mode to selct the voice recoding file you want to play press ok button to start playback of the voice recording file thru vivicam speaker..good luck hope this give you an idea somewhat..
Audio Dubbing may vary by model. Most Digital Camcorders are equipped with this feature. To verify that your model is, please view the User Manual.
* The AUDIO DUBBING function only works in PLAYER Mode.
* You can add sound to the original sound on a pre-recorded tape, recorded in SP mode with 12bit sound.
* Use the internal and external microphones or other audio equipment.
* The original sound will not be erased.
1. Set the camcorder to PLAYER mode.
* If you want to use an external microphone, connect the microphone to the external MIC input jack on the camcorder.
* When you wish to dub using the External A/V input, connect the AUDIO/VIDEO cable to the camcorder by inserting the cable jack into the A/V in/out terminal at the left side of the camcorder.
- Press the MENU button, turn the MENU DIAL to highlight A/V and press the ENTER button.
- Turn the MENU DIAL to highlight AV IN/OUT and press the ENTER button to select AV IN.
2. Press the (PLAY/STILL) button and find the timeframe of the scene to be dubbed.
3. Press the (PLAY/STILL) button to pause the scene.
4. Press the A.DUB button on the Remote Control.
* A.DUB will be displayed on the LCD.
* The camcorder is in a ready-to-dub state for dubbing.
5. Press the (PLAY/STILL) button to start dubbing.
* Press the (STOP) button to stop the dubbing.
* You can not use the audio dubbing function while playing a write protected video tape.
* When you wish to dub using the External A/V input, you must connect the AUDIO/VIDEO cable to the audio system from which you wish to record.
* You cannot dub sound on a pre-recorded tape in LP or 16 bit mode.
Dubbed audio Playback
1. Insert the dubbed tape and press MENU button.
2. Turn the MENU DIAL to highlight A/V.
3. Press the ENTER button to enter the sub-menu.
4. Use the MENU DIAL to select AUDIO SELECT from the submenu.
5. Press the ENTER button to enter the sub-menu.
6. Using the MENU DIAL, select the AUDIO playback channel.
Press the ENTER button to confirm the audio playback channel.
* SOUND1 : play the original sound.
* SOUND2 : play the dubbed sound.
* MIX(1+2) : play back SOUND1 and 2 equally mixed.
7. To exit, press the MENU button.
8. Press the (PLAY/STILL) button to playback the dubbed tape.
Note: When you playback added sound (SOUND2 or MIX mode), you may experience loss of sound quality.