Question about Zanussi 24 in. DE6744S Free-standing Dishwasher

1 Answer

Oh No Now both the program light and the wash light are flashing together and the machine stops working altogether after a minute.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers
Re: Oh No

ANTI-FLOODING CONTROL SYSTEM ALARM [A L 4] Leds [LD9] + [LD10] This control system is operative during the washing phases only, and not in the water fill phases, in which case is it connected to the safety device (see paragraph 7.4.1 ?Water Fill Time-out?).  A float-actioned mechanical sensor positioned on the bottom of the appliance trips a microswitch which is connected in series to the fill solenoid, thus disconnecting the solenoid.  Intervention of the sensor is detected by the electronic control board, which actions the drain pump for 1 minute, after which an alarm condition is generated. Possible causes: a. Water leakage from the tub/sump seal b. Water leakage from the various couplings (motor, OR on the duct to the upper spray arm, etc.) c. Floating sensor jammed mechanically/microswitch faulty

Posted on Jul 15, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Electrolux (dishlex) DX302SJ dishwasher all lights flashing. When I press program and start buttons together code 1C flashes.

Take the kick panel off the bottom. There is a tech sheet in an envelope under the machine. IT will have everything that you need to do to troubleshoot the machine.

Dec 02, 2013 | Electrolux Dishwashers

1 Answer

Dishwasher stops after i minute

Hi, this is a control fault that is localized in the logic sector of the control board. the logic chip which holds all wash programing is damaged. you will need to replace the control asap if possible.

May 30, 2009 | Hotpoint Dishwashers

1 Answer

Indesit idl 40 2&3 lights flash

The problem is lack of water. Check that the water is turned on at the stop **** and make sure that the hose hasn't been traped if the dishwasher has been pulled out from it resess as happened to mine.

Jan 21, 2009 | Indesit 18 in. D41 Slim-Line Free-standing...

2 Answers

Dwf50 hotpoint aquarius dishwasher

hi, just found this forum after searching the web 4 a solution to my hotpoint DWF50 problem.
I came down this morning to a machine which base tray was full of water and lights 3 ECO & 4 Fast flashing.
Anyway my solution was as i had seen a hotpoint engineer do once before was to press the start/reset button trip the catch, to fool the machine into thinking the door is closed then put in a program, press start, the machine hums slightly but doesnt do anything then after removing the large filter from the tray at the bottom underneath the lower basket insert a length of wire, with a loop on the end (Tip i used a wire coat hanger from the dry cleaners) poke in ythe hole that the dirty water drains from, after a bit of poking about the pump started working and the water drained away. Tip place a hook at the other end of your wire impliment to put your finger in to stop the wire getting caught in the pump mechanisim. After wards u have to hook back the door catch to the normal position, Tip another piece of the coat hanger with a right angled piece at the end will do this. This worked for me, saved me some money esp as D & G insurance ran out 2 weeks ago.....stu

Jun 16, 2008 | Hotpoint 24 in. DWF32P Free-standing...

1 Answer

Dishwasher flashes on Fast Wash

I am hoping I have just fixed mine with same problem. Couple weeks ago started stopping at start of cycle with fast button flashing. Check filters so one on top of unside machine and one on tap if you have one on there. Mine were blocked but still wouldnt work. I pulled out machine to find a kink in the water pipe. I have straightened this out and up to now its working. Fast button flashing refers to water inlet problem.

Feb 27, 2008 | Dishwashers

2 Answers

ZDT5052 flashes quickwash light

Tarvi...I don't know what the problem is...hard to diagnose these things. If the unit is working correctly, I suggest that you simply cut the power for a few minutes and then restart it. That may clear our a trouble code.

Dec 06, 2007 | Zanussi 18 in. ZDT5052 Slim-Line Built-in...

1 Answer

Bosch SHU5318: Water wont start washing

if it hums when you are in the wash phase then something is jamming the wash impeller like broken glass tooth pick found a necklace in one one time i think replacing the control board fixed the other problems on most washers the drain pump is separate from the wash motor haven't worked on bosch so not sure take off the lower spray arm and go down till you get to the impeller then do what you have to do clear it or replace wash motor

Dec 01, 2007 | Bosch 24 in. SHU53 Built-in Dishwasher

1 Answer

Asko 1585 Dishwasher

do they flash lik all on one side then the other? Start a cycle, then open the door. Do the lights flash the same way when you open the door as when it stops? if soyou may have a door that needs to be adjusted so it closes better. when the cycle ends, is there any standing water in the bottom? if so you may have a poorly routed drain hose or a partial clog in it. Last, pull the bottom panels off and look inside the bottom of the dishwasher and see if there is standing water down there . If ther is you have aleak somewhere or a bad drain pump. You r only other choice is a bad pressure switch. If youve already adjusted the water fil to the proper level ( just up to the grey plastic housing that the lower wash arm sits on) tehre really aernt any more options. Hope this helps!

Aug 29, 2007 | Asko 24 in. 1585 Built-in Dishwasher

1 Answer

Machine won`t fill

the water-inlet solenoid valve is inoperative-replace it

May 30, 2007 | Zanussi 24 in. DE6544 Built-in Dishwasher

1 Answer

Flashing lights

You have a heat problem, using a test meter check the heater element, then check the thermostat if niether of these you have a PCB fault Regards Engineer

Mar 15, 2007 | Indesit 23 in. DV62 IX Built-in Dishwasher

Not finding what you are looking for?
Zanussi 24 in. DE6744S Free-standing Dishwasher Logo

473 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers


Level 3 Expert

1751 Answers

Are you a Zanussi Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides