Question about Hotpoint Ariston Aquarius WD420 Front Load All-in-One Washer/Dryer

2 Answers

Hoover easy logic error message number 3

Any ideas on this one pls

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,559 Answers

The manual states that error 3 is due to overloading.
Are there any other codes?

Please rate this fixya

Posted on Jan 25, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,550 Answers

Thermistor Failure

When the thermistor circuit is open the error code flashes .

You need to replace it .

Posted on Jan 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My hoover washing machine model dyn d8p has a code error of ao3/t know what is wrong ..its new and just used then 3 month now but it was not drying well and showing that error code


if it is 3 months old , I suggest that you call the repair shop as it is under warranty
touching it yourself or having any unauthorised person fix it will void the warranty.

Apr 10, 2015 | Hoover Washing Machines

1 Answer

I have a Hoover H160i that is coming up with E05 error. Any ideas?


Thank you. I ran a 2 and 3 wash (60 and 40 degree wash). It allowed me to put it onto a rinse/spin/cycle but it didn't allow the wash.

Nov 28, 2012 | Hoover H160I Front Load Washer

1 Answer

I need a replacement door for my Hoover Easy Logic 1100 aa Washing machine. I beleive that the model is discontinued but my machine is in perfectly good working order. Could you advise anywhere where I...


I searched for quite some time without success and I am Pretty good at finding things.

Contact Hoover using this link:
http://service.hoover.co.uk/spares

To order Hoover Genuine Spares & Accessories please call 08443 712758
Opening hours: Mon-Fri 8.30am - 5pm.

I could not even come up with the part number for the door. I did find the following:
1. Door Seal
2. Door Glass
3. Door Handle
4. Door Hinges

No luck on finding the complete door assembly.
Another alternative... if the Yorkshire area has an appliance recycling venter you may be able to find one there or in the classified ads "for parts only" But then your faced with disposing of the "junk."
I recommend you contact Hoover using the number or Lonk above and see what they can do for you.

I wish I could have done more for you but the whole door assembly just does not seem to be readily available.

Thanks for choosing FixYa,
Kelly

Sep 03, 2011 | Washing Machines

1 Answer

The door on my hoover easy logic 1100aa washing machine will not open. The wash is complete and there is power???


is this one of the newer HE machines?

the washer may not recognize that the cycle is complete even though you think and see that it has -- can you try running another cycle?

Best regards
Ck

Jan 05, 2011 | Hoover Washing Machines

1 Answer

Hoover easy logic error message number 3 model is a EL 160


E3 indicates Drain pump faulty; Wiring faulty; PCB faulty.

The service information also says it should stop with the door open.



Unplug the appliance and manually remove the water via the filter or front drain point if it's fitted.

Drain it into a shallow dish, tighten the filter when you need to stop the water (or plug the hose if draining via a hose) while you empty the container.



Once empty, try the door again.

Take the filter out and clean out any debris in it.

Plug the appliance in and put the machine on a drain program.

Listen/look at the open filter to check that the drain pump is running.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Jan 25, 2009 | Washing Machines

1 Answer

Error code SE how to fix it what dose it mean


Hi,

To my knowledge, error code "SE" indicates a sensor fault. The sensor is attached at the end of the motor. Its function is to monitor the speed and direction of rotation. If the sensor is faulty, the logic controller would not be getting one of its inputs and therefore would halt the system operation. It is relatively easy to replace since it is only held by a single screw and attach to a single connector. There are however a few instances that the sensor is OK, it is the wiring/attachment to the controller board that is faulty or the controller board itself.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information. Good luck and kind regards. Thank you for using FixYa.

Nov 08, 2008 | LG Washing Machines

1 Answer

No manual for Hoover Logic 1250


try here you must have your model number off the serial plate on the washer http://service.hoover.co.uk/manuals/?Section=2

Mar 12, 2008 | Washing Machines

2 Answers

Program don't start, flashing ligths (start and "delay start" button) for 5 times.


What does the error code mean do you have any idea Is it mentioned in the Hand book. At any rate logic suggests a watewr supply problem that the first thing a washing machine needs - water. So a tap not turned on a Kinked hose An inlet valve solenoid failure- Three things for you to check

Jul 31, 2007 | Hoover Nextra HNWL 3136 Front Load Washer...

Not finding what you are looking for?
Hotpoint Ariston Aquarius WD420 Front Load All-in-One Washer/Dryer Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...