Question about LG WM2688H Front Load Washer

1 Answer

I have water leaking back into the drum after completed cycle. There was no water when cycle was completed. It start as very little water, but today the whole bottom of the tub was full.

This problem start intermittently a acouple months ago. It has gotten worse the last couple weeks. The cycle will be comlete and clothes removed and there is no water in the drum. But When I come back the next day or so there is water standing in the drum. It has went from very little water to the bottom of the tub being full this am. I have been running a spin aone cycle to empty before I do a load. A couple of times it has not spun all the water out when washing a load( very few times), and I have had to run a spin cycle to get water out of clothes. We have cleaned out filter basket--not much was in there and there was alot of water this am.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 66 Answers

Need need water values

Posted on Jan 18, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1462 Answers

SOURCE: Loud squeaky Noise

this is not 100% diagnosis as can't listen to noise but fault may be bearing lip seal disintegrating which is a serious fault and if im right then bearing will shortly go as well. reason it is noisy during start is that seal is dry and gets wet when full of water

Posted on Apr 19, 2007

SOURCE: Water in detergent dispenser

Remove dispencer again, remove conditioner syphon assembly and clean up the little tube. Should then go okay

Posted on Jul 11, 2007

  • 1294 Answers

SOURCE: LG WM2077CW (UE error code)

For "ue" an unbalanced load is sensed three times; re-adjust your load in the machine. What is the capacity of your machine, you could weigh your dry clothes........refer manual.

For e1, it could be a water sensor problem. Check to see if the inlet valve is okay and not clogged, water shd be in good pressure. If this is okay, open up behind after taking the plug off the wall. There is a thin tube coming from the switch area to the outlet pump area; disconnect this from the top carefully and blow into it, it should be free; if it is clogged you will hav a water level problem. Unblock and refit carefully.
.....& rate me if helped.

Posted on Jan 29, 2008

  • 489 Answers

SOURCE: soap dispenser not working

It sounds like the water valve has a clogged filter.  Shut the cold water to the washer off, disconnect the hose and remove the filter screen in the washer water valve.  Clean out the filter with toothbrush.  Reinstall and everything should be ok.

Posted on Apr 28, 2008

  • 1 Answer

SOURCE: LG WM1814CW - Water/soap Leaking Under Washing Machine onto Floor

Here is the answer !!! My LG front loader has leaked once a year for the past 4 years. The rubber bellows (a part underneath the washer) cracks and causes the leak. DO NOT LET THEM TELL YOU THAT YOU ARE USING TOO MUCH DETERGENT ... THAT JUST AN EXCUSE !!! The part costs around $12. Here's the link ...

http://www.repairclinic.com/SmartSearch/SmartSearch.aspx?R=1514&searchText=LG%20Washer

Posted on Oct 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Miele W1119 washer won't run. It was fine earlier today and I just completed a load of wash. When I started the next load on the Normal cycle, the timer lights to 58 minutes as always and the...


sounds like bushes mine done the same changed them now all good check it is not leaking water on to the bottom of machine this will activate the sensor to stop washing and drain water

Jun 04, 2017 | Miele Touchtronic W1119 Large Capacity...

1 Answer

Washer leaking water on floor


Hi

The water leaking on floor can be a serious issue as this may cause the inside parts to malfunction or in some cases rusting of the body. To check where exactly it is leaking; inspect the leak while it is running. After the cycle is complete quickly turn off the power, lie down the machine on left/right side and check from where the water is leaking. If it is the hose or drain pump then check whether hose is connected firmly and is not cut. If it not the hose/pump inspect if the leak is on the drum corner or anywhere on the upper side of the drum. If it is on upper side that means the drum is cracked and it is a costly affair. However, if it is leaking from the circumference then it is due to transmission seal. To replace the transmission seal you'll need to disassemble the washer and the drum assembly. Please post back in case of any issues. Hope this helps...

Daniel

Feb 11, 2011 | Frigidaire GLET1031WH Top Load Stacked...

1 Answer

Water leaking from bottom of washer between the washer and petestal


Hi

The water leaking on floor can be a serious issue as this may cause the inside parts to malfunction or in some cases rusting of the body. To check where exactly it is leaking; inspect the leak while it is running. After the cycle is complete quickly turn off the power, lie down the machine on left/right side and check from where the water is leaking. If it is the hose or drain pump then check whether hose is connected firmly and is not cut. If it not the hose/pump inspect if the leak is on the drum corner or anywhere on the upper side of the drum. If it is on upper side that means the drum is cracked and it is a costly affair. However, if it is leaking from the circumference then it is due to transmission seal. To replace the transmission seal you'll need to disassemble the washer and the drum assembly. Please post back in case of any issues. Hope this helps... Please post back if you need more information.

Daniel

Dec 11, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

My washer won't drain near end of cycle. Motor


Hi,
The problem will be on the main board or the power supply board of the machine might have some problem kindly the check the wire lines as well

i do not think that drain pump is having any problem

Dec 30, 2009 | Kenmore 42822 Front Load Washer

1 Answer

Water Everywhere


Look for loose, cracked, pinched, broken hoses to and from the water pump or leaks from the water pump itself. The outer drum could have a rust-through that leaks. This can be repaired with epoxy, but the inner drum must be removed to access it. The cabinet top is opened by using a putty knife or similar tool to push straight back under each front corner which releases a spring latch. Sometimes, the drain hose outlet is pushed from the house drain by high water flow. Tie the hose to the drain with tape or cord. Fill the tub with water, then stop the cycle and watch for leaks.

Aug 07, 2009 | GE WBSR3140DW Top Load Washer

1 Answer

Water is collects in drum after a few hours after cycle is complete


no your inlet water valve is defective, youll need to repalce it, part number 8181694. in the mean time just turn off water in beween usages.

Oct 29, 2008 | Kenmore Elite 45986 Front Load Washer

1 Answer

Maytag front load leaking at drum spider


Probably not. Sounds like bearings and seal is shot.

Sep 08, 2017 | Washing Machines

1 Answer

WASHES BUT WILL NOT SPIN


If your washer pumped out the water then your motor and water pump are both still working. Your washer has many sets seals and bearings that could have gone bad. This problem happened to my washer in the past also and i was able to just spin the drum around a few times and then shut the lid on the spin cycle. It started spinning slow but was able to make speed quickly. The oil seal on the gear case did start leaking though. This should be a cheap fix that could be done by most people with some mechanical ability.

Feb 14, 2008 | Washing Machines

Not finding what you are looking for?
LG WM2688H Front Load Washer Logo

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top LG Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...