Question about Nespresso Lattissima 660.R

1 Answer

I have a Nespresso Lattisima and all four lights are blinking four times in quick succession and nothing is working. I've tried emptying it out and it's done that, but still the same problem.

Was starting to make a latte and it stopped half way through and all lights started blinking. I've cleaned it out (manually, as per instructions), emptied it out. As it's brand new, can't see it needs descaling (and orange light not on). Nothing else seems to be out of order, and it's been working perfectly for one week. Took the milk compartment out to see if I could make just normal espressos and can't. It won't do a'thing now except blink (all lights at same time, four times in quick succession).

Posted by on

  • Tamikh Jan 17, 2013

    I've tried it again, and it will start to make a coffee (ie sounds like it's working) but then it seems to think it is still emptying, as water then comes out into the drip tray. So keep going through the emptying process again as it seems to think it's in that mode. Don't know how to 'reset'.

  • Tamikh Jan 17, 2013

    And now that I've done that (emptying) again, just four blinks all the time. Won't do anything. Had a power outage last night, but have surge protectors, so assuming that all is ok. Anyway, it switches itself off, so shouldn't have affected it.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Your machine has almost certainly entered the water quality mode. (Water hardness setting). This is very easy to fix. Switch machine off. Before switching back on press and hold any off the following buttons: Latte Macchaito (top right) for soft water, Cappuccino (bottom right) for medium water or finally both of them for hard water. While holding the correct buttons switch the machine back on BUT hold for approx. 10 seconds or until all lights stop flashing, (APART FROM THE BUTTON YOUR HOLDING). This will reset the machine and you're good to go. Regards Coffee Engineer!

Posted on Apr 10, 2018

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 333 Answers

SOURCE: Brand New Nespresso Essenza just stopped working..

If you just bought it you should return it immediately and try another.

Posted on Dec 24, 2008

  • 1 Answer

SOURCE: Too little coffee

1080p60 is a genius! 
he is correct. the owner's manual gives you the impression that it is a three step process: 1) turn machine off. 2) push large coffee cup icon. 3) turn machine back on. BUT it does not make it clear that after turning the machine off, you must hold the coffee cup icon down WHILE turning the machine on. solved the problem perfectly. thank you 1080p60! 

Posted on Dec 27, 2008

  • 1 Answer

SOURCE: I have a new Nespresso Machine from DeLonghi. I

screen is flashing blue (craig player 4gb mp4

Posted on Dec 06, 2009

  • 8 Answers

SOURCE: The Nespresso won't make coffee yellow light keeps blinking

This is because there is either too much water in the drip tray, the empties container is full or the drip tray is not placed correctly. This took me a while to figure out as well, and the manual was little help. Nespresso is located in Switzerland so their support number is international. Hope this helps someone...

Posted on Sep 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Descaling problems


Don't run the clean operation. Just put white vinegar/ water, half and half and run as if making coffee. Let it cool and run through about 3 times and this will remove all scaling/buildup.The rune through plain water.

Nov 08, 2013 | Coffee Makers & Espresso Machines

2 Answers

Just bought my 4runner and noticed there's two blinking lights on my dash. It looks like it has something to do with the the switch that says h4-h2. My car didn't come with a manual! I've


go back to the dealer and get the user manual and the service and warranty book ( new car)
or is it an old car that is new to you
in which sweet talk a dealer salesman to show you what operates what

Dec 11, 2017 | 2007 Toyota 4Runner

1 Answer

Obd2 code p0562


Low battery charge, Battery Defective(Could have a bad cell), Loose or missing alternator drive belt, Faulty Alternator, Open or short system voltage circuit

Apr 11, 2017 | Mazda RX8 Cars & Trucks

1 Answer

OBD2 CODE READER P0562


Make sure your 12V grounds to engine and chassis are good.

Apr 11, 2017 | Mazda RX8 Cars & Trucks

1 Answer

Candy CDB 854: Just installed, spin tested briefly. Now just lights and no function.


Turn the power back on, go through the instruction book to start the machine up. If its still not right, call the Service Agent. Its brand new and will be covered by warranty.

Apr 26, 2017 | Computers & Internet

1 Answer

I have a Philips 42pf5321d/37 that won't turn on.


send me a email sonny@tvcircuitboards.com and I can assist you with troubleshooting it to determine whats happening with the set.

Aug 07, 2012 | Televison & Video

1 Answer

I'm following the instructions on my Whirlpool range to clean the oven. I've done everything the instructions said, but it won't get going. ( set the knob to clean, set start and stop knobs...


Might be a typo in the manual typically the latch is moved to the right to close and after clean is over move to the left to open. BE SURE TO REMOVE RACKS BEFORE CLEANING

Aug 11, 2011 | Whirlpool Ovens

1 Answer

Tv turns on for a few seconds then shuts off and the blue power light blinks.


Mine never turned on but the blue power light would blink.I disconnected the upper y buffer and got light on the bottom half of screen and the blinking stopped.I have the upper board on order and I think this will fix my problem.There is a blink code somewhere,just count how many blinks.Start pulling connectors from power supply and when it quits blinking you've found the one,could also be the power supply with bad cap.

Jul 14, 2011 | Hitachi Ultravision P50S601 50 in. Plasma...

1 Answer

EZ3612 - spins for couple of times then stops with burning smell and mode light blinking 13 times


Per the service manual, if the mode light blinks 13 times, there's a bad dryer sensor or thermostat. I'm not sure if that related to your problem but it's a start.

Doug

Feb 24, 2008 | Equator EZ 3612 CEE Front Load...

Not finding what you are looking for?
Nespresso Lattissima 660.R Logo

Related Topics:

3,690 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nespresso Coffee Makers & Espresso Machines Experts

Joseph Hoffmann

Level 3 Expert

1746 Answers

Kolbrun...

Level 3 Expert

1214 Answers

Jay Finke
Jay Finke

Level 3 Expert

1383 Answers

Are you a Nespresso Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...