Question about Dell Dimension 4600 PC Desktop

1 Answer

Installing memory cards

I need step by step instructions...Including the removal of the cover Preferaby in print version, thanks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 40 Answers

Hello,
Obtain this free pdf from Dell support website-->http://support.dell.com/support/edocs/systems/dim4600C/en/H72280.pdf
Pages--57 to 61 Instructs on opening the cover and shows the parts of the systemboard.
Pages--68 to 71 Instructs on adding and removing the memory.
I hope this helps! Let me know if you have any questions.
Thank  You, Raph30

Posted on Jan 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need step by step instruction for installing memory


First check that you have bought the correct RAM.
Go to www.Crucial.com and select 'Get the correct memory'. and check the results with what you have.
If OK probably best to remove an existing RAM chip noting carefully how it comes out and which way round.
Broadly, there is a catch at the bottom on each side, that has to be released (with a small electrical screwdriver) then you pull up at an angle of 45 deg..The slot in the centre of the RAM will only match one way round. Then replace it and try the same with your new RAM in the next empty slot.

Apr 02, 2014 | MPC Computers ClientPro 414 All-In-One PC...

1 Answer

Installing internal dell m90 smart card reader


You have to take apart a good portion of the laptop to reach the Smart Card Reader spot. You need to turn off the computer, unplug the AC power and remove the battery first. Make sure that you are grounded to the computer. Then remove your optical drive and the hinge cover. Next you remove the mini-card antennas either from the mini-card or their secure spot, display assembly, the keyboard and the palm rest. Then you can reach the screw for the smart card reader and the place on the motherboard where the smart card reader connects.
The full set of steps and pictures is available from the Dell support site, http://www.dell.com/support/Manuals/us/en/19/product/precision-m90 . See the Workstation Service Manual. The direct link to the English version is ftp://ftp.dell.com/Manuals/all-products/esuprt_laptop/esuprt_precision_mobile/precision-m90_service%20manual_en-us.pdf . There are multiple pages you need to follow.
I hope this helps.
Cindy Wells

Jul 06, 2013 | Dell Precision PC Desktops

1 Answer

I want upgrade my emachines t6528 hard drive and ram.i need help


Memory Upgrade for eMachines eMachines T6528 Computer, the eMachines eMachines T6528 Computer takes the PC3200 DDR SDRAM DIMMs. Supports Dual Channel DDR. Memory Type, and comes installed with 512 MB (removable) of Memory. You can upgrade your eMachines eMachines T6528 Computer to up to a maximum of 4.0 GB Memory, the system has 4 sockets to install Memory, already with 512 MB (removable) standard Memory installed. For best Computer performance use the maximum amount of allowed Memory per slot for your Computer.


As for the Hard Disc.... the following address will give step by step instructions on installing a new HD. http://www.manualowl.com/m/eMachines/T6528/Manual/

Thank You for using FixYa
Tom Miller
KD4DTK

Aug 19, 2012 | E-Machines T6528 PC Desktop

1 Answer

HP4550 - 49.00FF service error


Turn off the RAM disk on the printer.

Follow these steps:

Troubleshooting steps

1.
Verify that the formatter light is blinking or steady. If the formatter is blinking, it is functioning properly and probably does not need to be replaced. If the formatter light is not blinking, proceed to Step 2.
2.
Turn off the printer and unplug the power cord.
3.
Remove the HP Jetdirect card, third-party device, hard disk, parallel cable, or IFR cable from the formatter if one is installed.
4.
If the error continues with accessories removed from the formatter, perform a cold reset on the printer. Ensure the HP Jetdirect card is not in the printer during a cold reset or the card settings will be changed back to default settings. To perform a cold reset, do the following:
1.
Turn on the printer.
2.
Watch the control panel.
3.
When the memory starts counting, press and hold the green (Select ) button.
4.
Continue holding the green check button until the Ready, Data, and Attention lights flash once, and then stay on steady.
5.
Release the check button when the Ready, Data, and Attention light are on steady.
The control panel will display SELECT LANGUAGE .
6.
Press (Down Arrow ) button once. The control panel will display COLD RESET
7.
Press (Select ). The printer will perform a cold reset and then continue its power-on sequence.
5.
If the printer comes up to ready, print a Configuration page. If a 49 error occurs from printing internal pages, continue on to the next step.
6.
Turn the printer off and unplug the power cord.
7.
Remove the eight screws around the formatter.
8.
Remove the formatter. See Figure 1.
9.
Reseat the firmware and memory modules on the formatter. Check for any DIMMs that are non-HP and remove them. Non-HP DIMMs are not supported by HP and may cause this error. Replace with HP DIMMs, if necessary.
10.
Reseat the daughter (interconnect) board. The daughter board is connected to the formatter behind EIO slot #1. To release the daughter board, push in the black retaining tab underneath the formatter then lift up the one side of the daughter board.
11.
Reseat the daughter board.

12.
Install the formatter.
13.
Turn the printer on again.
14.
If it comes up to READY , print a configuration page. If a 49 error does not appear from printing internal pages, or at power up, continue to the next step.

15
Install the HP Jetdirect card and hard disk before installing the formatter. Verify that each device is properly seated.
16
Test any EIO devices, by turning off the printer, installing each device separately, and printing a Configuration page. Repeat for each EIO device.
17
If the 49 error occurs with any EIO device installed, replace that EIO device.

Oct 05, 2010 | PC Desktops

1 Answer

How do you remove the cover off of a Dell APC. I


Here's a link to your owners guide. Go to page 69 for step by step instructions on removing the cover.

http://support.dell.com/support/edocs/systems/dim8400/en/om/U70350LRs.pdf

Please take time to rate the solution...thanks!

Oct 15, 2009 | Dell Dimension 8400 PC Desktop

1 Answer

How to open sony vaio-pcv-w101/w to replace bad ram?


Try this:
STEP 11
Lift up and remove notebook display panel.
13-taking-apart-notebook.jpg STEP 12
Remove hard drive cover, memory cover and modem cover from the bottom of the notebook. Each cover is secured by one screw.
14-taking-apart-notebook.jpg STEP 13
Here’s how you can remove the hard drive. Remove four screws securing the hard drive caddy to the base assembly. Slide the hard drive down to disconnect it from the motherboard. Lift up and remove the hard drive.
15-taking-apart-notebook.jpg STEP 14
Removing memory modules (if needed). Carefully spread latches on both sides of the memory slot. The memory module will pop up at 30 degree angle. Pull the memory module from the slot by the edges.
Removing modem card (if needed). Remove two screws securing the modem card. Lift up the modem card to disconnect it from the motherboard and unplug cable from the side.

Hope this Helps

DR GEEK MD

May 06, 2009 | Sony VAIO VGC-V617G PC Desktop

1 Answer

Can not print because pc is out of memory


Hi,

I would appreciate if you coulld tell me whats the version of Ms works you are using ??
Can try some steps :--
Try these steps first

Printer and Faxes (Start>Settings or via Control Panel )


Right-click on the printer's name.
Select 'Properties'.
Select the 'Advanced' tab
Select 'Print directly to printer'.
If that still doesn't solve the problem you may need to completely uninstall works and use the works and Windows cleanup utility before reinstalling.

http://support.microsoft.com/?kbid=816273
Bur before we uninstall I would like to know the version, hope i can diagnose this in a better way.
Awaiting response
Thanks

Mar 30, 2009 | PC Desktops

1 Answer

Installing a 2nd 256m ram memory card into packard bell imedia3501


Installing more memory to a pc is very universal and is done the same way into all computers out there.

First unplug your pc
e91ab01.jpg
Open the side cover or remove the cover debending on your pc case.

26fd016.jpg
Turn the pc sideways on the floor or table
and locate the memory slots near the cpu.

119c6f9.jpg
In this pc we have 3 memory modules installed
In this case I would have to remove one of the original memory modules first before installing a new one.

But in your computer you should have a extra slot open.

Simply insert the memory into the slot and turn the white switches on the sides to lock the memory in.

And you are done.

Jul 01, 2008 | Packard Bell PC Desktops

3 Answers

Memory upgrade


most laptops have a cover that is held in by one or more screws on one end .

good luck
Terry

Mar 26, 2008 | PC Desktops

Not finding what you are looking for?
Dell Dimension 4600 PC Desktop Logo

Related Topics:

211 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dell PC Desktops Experts

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18297 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a Dell PC Desktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...